Datasheet

SN75ALS193
QUADRUPLE DIFFERENTIAL LINE RECEIVER
SLLS008D – JUNE 1986 – REVISED MAY 1995
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended range of common-mode input voltage, supply
voltage, and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS
†
MIN TYP
‡
MAX UNIT
V
IT+
Positive-going input threshold voltage 200 mV
V
IT–
Negative-going input threshold voltage –200
§
mV
V
hys
Hysteresis voltage (V
IT+
–V
IT–
) 120 mV
V
IK
Enable-input clamp voltage V
CC
= MIN, I
I
= – 18 mA –1.5 V
V
OH
High level out
p
ut voltage
V
CC
= MIN,
V
ID
= 200 mV,
25
36
V
V
OH
High
-
le
v
el
o
u
tp
u
t
v
oltage
CC
,
I
OH
= –400 µA,
ID
See Figure 1
2
.
5
3
.
6
V
V
OL
Low level out
p
ut voltage
V
CC
= MIN,
V
ID
200 mV
I
OL
= 8 mA 0.45
V
V
OL
Lo
w-
le
v
el
o
u
tp
u
t
v
oltage
V
ID
= –
200
m
V
,
See Figure 1
I
OL
= 16 mA 0.5
V
I
OZ
High im
p
edance state out
p
ut current
V
CC
= MAX
V
O
= 2.4 V
20
µA
I
OZ
High
-
impedance
-
state
o
u
tp
u
t
c
u
rrent
V
CC
=
MAX
V
O
= 0.4 V
–20
µ
A
I
I
Line in
p
ut current
Other input at 0,
V
CC
= MIN,
V
I
= 15 V
0.7 1.2
mA
I
I
Line
inp
u
t
c
u
rrent
,
See Note 3
V
CC
= MIN,
V
I
= –15 V
–1.0 –1.7
mA
I
IH
High level enable in
p
ut current
V
CC
= MAX
V
IH
= 2.7 V
20
µA
I
IH
High
-
le
v
el
enable
-
inp
u
t
c
u
rrent
V
CC
=
MAX
V
IH
= MAX 100
µ
A
I
IL
Low-level enable-input current V
CC
= MAX, V
IL
= 0.4 V –100 µA
Input resistance 12 18 kΩ
I
OS
Short-circuit output current
V
CC
= MAX,
V
O
= 0,
V
ID
= 3 V,
See Note 4
–15 –78 –130 mA
I
CC
Supply current V
CC
= MAX, Outputs disabled 22 35 mA
†
For conditions shown as MIN or MAX, use the appropriate values specified under recommended operating conditions.
‡
All typical values are at V
CC
= 5 V, T
A
= 25°C.
§
The algebraic convention, in which the less positive limit is designated minimum, is used in this data sheet for threshold voltage levels only.
NOTES: 3. Refer to ANSI Standard EIA/TIA-422-B and EIA/TIA-423-A for exact conditions.
4. Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second.
switching characteristics, V
CC
= 5 V, T
A
= 25°C
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
t
PLH
Propagation delay time, low-to-high-level output
V
ID
= –2.5 V to 2.5 V,
15 22
t
PHL
Propagation delay time, high-to-low-level output
ID
,
C
L
= 15 pF, See Figure 2
15 22
t
PZH
Output enable time to high level
C
L
=15
p
F See Figure 3
13 25
ns
t
PZL
Output enable time to low level
C
L
=
15
pF
,
See
Fig
u
re
3
11 25
ns
t
PHZ
Output disable time from high level
C
L
=5
p
F See Figure 3
13 25
t
PLZ
Output disable time from low level
C
L
=
5
pF
,
See
Fig
u
re
3
15 22