Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - receivers RS232 0/4 PDIP 16

SN75154

QUADRUPLE LINE RECEIVER

SLLS083B – NOVEMBER 1970 – REVISED MAY 1995

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

Meets or Exceeds the Requirements of

ANSI Standard EIA/TIA-232-E and ITU

Recommendation V.28

Input Resistance . . . 3 kΩ to 7 kΩ Over Full

EIA/TIA-232-E Voltage Range

Input Threshold Adjustable to Meet

Fail-Safe Requirements Without Using

External Components

Built-In Hysteresis for Increased Noise

Immunity

Inverting Output Compatible With TTL

Output With Active Pullup for Symmetrical

Switching Speeds

Standard Supply Voltages ...5 V or 12 V

description

The SN75154 is a monolithic low-power Schottky line receiver designed to satisfy the requirements of the

standard interface between data terminal equipment and data communication equipment as defined by ANSI

Standard EIA/TIA-232-E. Other applications are for relatively short, single-line, point-to-point data transmission

and for level translators. Operation is normally from a single 5-V supply; however, a built-in option allows

operation from a 12-V supply without the use of additional components. The output is compatible with most TTL

circuits when either supply voltage is used.

In normal operation, the threshold-control terminals are connected to the V

CC1

terminal, even if power is being

supplied via the alternate V

CC2

terminal. This provides a wide hysteresis loop, which is the difference between

the positive-going and negative-going threshold voltages. See typical characteristics. In this mode of operation,

if the input voltage goes to zero, the output voltage will remain at the low or high level as determined by the

previous input.

For fail-safe operation, the threshold-control terminals are open. This reduces the hysteresis loop by causing

the negative-going threshold voltage to be above zero. The positive-going threshold voltage remains above

zero as it is unaffected by the disposition of the threshold terminals. In the fail-safe mode, if the input voltage

goes to zero or an open-circuit condition, the output will go to the high level regardless of the previous input

condition.

The SN75154 is characterized for operation from 0°C to 70°C.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

GND

CC2

CC1

†

(TOP VIEW)

D OR N PACKAGE

†

For function of R1, see schematic

Summary of content (16 pages)

PAGE 1
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 D D D D D D D D OR N PACKAGE (TOP VIEW) Meets or Exceeds the Requirements of ANSI Standard EIA/TIA-232-E and ITU Recommendation V.28 Input Resistance . . .
PAGE 2
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 logic symbol† 1A 1T 2A 2T 3A 3T 4A 4T logic diagram (positive logic) 4 3 5 13 THRS ADJ 12 2 6 11 1 7 10 14 4 1A 1Y 1T 5 2A 2Y 12 6 3A 2Y 11 3Y 1 3T 7 4A 4Y 1Y 2 2T 3Y 13 3 10 4Y 14 4T † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. schematic Common to Four Receivers VCC2‡ 3.2 kΩ VCC1 5 kΩ R1 GND 1 of 4 Receivers Threshold Control 1.6 kΩ 5.5 kΩ 1.
PAGE 3
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Normal supply voltage, VCC1 (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Alternate supply voltage, VCC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 V Input voltage, VI . . . . . . .
PAGE 4
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) TEST FIGURE PARAMETER Normal operation VIT IT+ Positive-going g g input threshold voltage Fail-safe operation VIT IT– Negative-going g g g input threshold voltage Fail-safe operation Vh hys Hysteresis y voltage g (VIT+ – VIT–) VOH VOL ri VI(open) IOS Normal operation Normal operation Fail-safe operation 1 1 1 Hig
PAGE 5
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs INPUT VOLTAGE VO V O – Output Voltage – V 4 ÁÁ ÁÁ VCC1 = 5 V TA = 25°C 3 Normal Operation 2 See Note A Fail-Safe Operation VIT – VIT + VIT – 1 0 – 25 –4 –3 –2 –1 0 1 VI – Input Voltage – V 2 3 4 25 NOTE A: For normal operation, the threshold controls are connected to VCC1. For fail-safe operation, the threshold controls are open.
PAGE 6
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION dc test circuits† TEST TABLE TEST MEASURE A T Y Open circuit input (fail safe) Open-circuit VOH VOH Open Open Open Open IOH IOH VIT + min, min VIT – min (fail safe) VOH VOH 0.8 V Open 0.8 V Open IOH IOH VIT + min (normal) VOH VOH Note A VCC1 VCC1 IOH IOH 5.5 V and T Open T 13.2 V VIL max max, VIT + min (normal) VOH VOH –3 V IOH IOH 5.
PAGE 7
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION dc test circuits† (continued) TEST TABLE T 5V 12 V Open T VI A VCC1 VCC2 R1 Y Open GND VI II ri = VCC2 Open Open GND Open Open Open Open VCC1 GND T and 5 V Open GND Open Open Open 12 V Open Open GND VCC1 VCC1 T 12 V T GND VCC1 T Open Open Open Open II VCC1 5V Figure 3. Input Resistance 5.5 V 13.2 V TEST TABLE T T VCC1 VCC2 Open Open VCC1 5.
PAGE 8
SN75154 QUADRUPLE LINE RECEIVER SLLS083B – NOVEMBER 1970 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION Input 5V Output Open Open RL = 390 Ω T Pulse Generator (see Note A) VCC1 VCC2 R1 See Note C A Y CL = 50 pF (see Note B) GND TEST CIRCUIT 10 ± 2 ns 10 ± 2 ns 90% 3V 5V 90% Input 0V 3V 10% 10% –5 V tPLH tPHL 2V 2V 1.5 V Output 1.5 V 0.8 V 0.8 V tTHL VOL tTLH VOLTAGE WAVEFORMS NOTES: A.
PAGE 9
PACKAGE OPTION ADDENDUM www.ti.
PAGE 10
PACKAGE OPTION ADDENDUM www.ti.com 4-Jun-2007 to Customer on an annual basis.
PAGE 11
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN75154DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SN75154NSR SO NS 16 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.
PAGE 12
PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN75154DR SN75154NSR SOIC D 16 2500 333.2 345.9 28.6 SO NS 16 2000 367.0 367.0 38.
PAGE 13
PAGE 14
PAGE 15
PAGE 16
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.