Datasheet

SN74LVC1G3157
SCES424H –JANUARY 2003–REVISED MAY 2012 www.ti.com
Analog Switch Characteristics
T
A
= 25°C
FROM TO
PARAMETER TEST CONDITIONS V
CC
TYP UNIT
(INPUT) (OUTPUT)
1.65 V 300
Frequency
2.3 V 300
R
L
= 50 Ω, f
in
= sine wave
response
(1)
A or Bn Bn or A MHz
(see Figure 6 )
3 V 300
(switch on)
4.5 V 300
1.65 V –54
2.3 V –54
Crosstalk
(2)
R
L
= 50 Ω, f
in
= 10 MHz (sine wave)
B1 or B2 B2 or B1 dB
(between switches) (see Figure 7 )
3 V –54
4.5 V –54
1.65 V –57
Feed through C
L
= 5 pF, R
L
= 50 Ω,
2.3 V –57
attenuation
(2)
A or Bn Bn or A f
in
= 10 MHz (sine wave) dB
3 V –57
(switch off) (see Figure 8 )
4.5 V –57
3.3 V 3
C
L
= 0.1 nF, R
L
= 1 MΩ
Charge injection
(3)
S A pC
(see Figure 9 )
5 V 7
1.65 V 0.1
V
I
= 0.5 Vp-p, R
L
= 600 Ω,
2.3 V 0.025
Total harmonic
A or Bn Bn or A f
in
= 600 Hz to 20 kHz (sine wave) %
distortion
3 V 0.015
(see Figure 10 )
4.5 V 0.01
(1) Adjust f
in
voltage to obtain 0 dBm at output. Increase f
in
frequency until dB meter reads –3 dB.
(2) Adjust f
in
voltage to obtain 0 dBm at input.
(3) Specified by design
Switching Characteristics
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 5 and Figure 11)
V
CC
= 1.8 V V
CC
= 2.5 V V
CC
= 3.3 V V
CC
= 5 V
FROM TO
± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V
PARAMETER UNIT
(INPUT) (OUTPUT)
MIN MAX MIN MAX MIN MAX MIN MAX
t
pd
(1)
A or Bn Bn or A 2 1.2 0.8 0.3 ns
t
en
(2)
7 24 3.5 14 2.5 7.6 1.7 5.7
S Bn ns
t
dis
(3)
3 13 2 7.5 1.5 5.3 0.8 3.8
t
B-M
(4)
0.5 0.5 0.5 0.5 ns
(1) t
pd
is the slower of t
PLH
or t
PHL
. The propagation delay is calculated RC time constant of the typical on-state resistance of the switch and
the specified load capacitance when driven by an ideal voltage source (zero output impedance).
(2) t
en
is the slower of t
PZL
or t
PZH
.
(3) t
di
s is the slower of t
PLZ
or t
PHZ
.
(4) Specified by design
6 Submit Documentation Feedback Copyright © 2003–2012, Texas Instruments Incorporated
Product Folder Link(s): SN74LVC1G3157