Datasheet

www.ti.com
SN74AVCA406
MMC, SD CARD, Memory Stick, SmartMedia, AND xD-Picture Card
± 15-kV ESD-PROTECTED VOLTAGE-TRANSLATION TRANSCEIVER
SCES615H – OCTOBER 2004 – REVISED JANUARY 2007
CONFIGURATION 1 FUNCTION TABLE
(MODE0 = L, MODE1 = L)
INPUTS OPERATION
SIGNAL
CS0 CS1 9DIR (1-4)DIR MMC/SD Memory Stick/Memory Stick PRO
CLK.0 and CLK.1 forced low, SCLK.0 and SCLK.1 forced low,
H H X X
CLK-f.h forced Hi Z SCLK-f.h forced Hi Z
CLK.h to CLK.0 and CLK.1, SCLK.h to SCLK.0 and SCLK.1,
L L X X
CLK.0 to CLK-f.h SCLK.0 to SCLK-f.h
CLK.h to CLK.0, SCLK.h to SCLK.0,
Clock
L H X X CLK.0 to CLK-f.h, SCLK.0 to SCLK-f.h,
CLK.1 forced low SCLK.1 forced low
CLK.h to CLK.1, SCLK.h to SCLK.1,
H L X X CLK.1 to CLK-f.h, SCLK.1 to SCLK-f.h,
CLK.0 forced low SCLK.0 forced low
H H X X All data I/Os are Hi Z (isolation mode). All data I/Os are Hi Z (isolation mode).
DAT0.0 and DAT0.1 to DAT0.h, DATA0.0 and DATA0.1 to DATA0.h,
DAT1.0 and DAT1.1 to DAT1.h, DATA1.0 and DATA1.1 to DATA1.h,
L
(1)
L
(1)
X L
DAT2.0 and DAT2.1 to DAT2.h, DATA2.0 and DATA2.1 to DATA2.h,
DAT3.0 and DAT3.1 to DAT3.h DATA3.0 and DATA3.1 to DATA3.h
DAT0.h to DAT0.0 and to DAT0.1, DATA0.h to DATA0.0 and to DATA0.1,
DAT1.h to DAT1.0 and to DAT1.1, DATA1.h to DATA1.0 and to DATA1.1,
L
(1)
L
(1)
X H
DAT2.h to DAT2.0 and to DAT2.1, DATA2.h to DATA2.0 and to DATA2.1,
DAT3.h to DAT3.0 and to DAT3.1 DATA3.h to DATA3.0 and to DATA3.1
DAT0.0 to DAT0.h, DATA0.0 to DATA0.h,
DAT1.0 to DAT1.h, DATA1.0 to DATA1.h,
L H X L
DAT2.0 to DAT2.h, DATA2.0 to DATA2.h,
Data DAT3.0 to DAT3.h DATA3.0 to DATA3.h
DAT0.h to DAT0.0, DATA0.h to DATA0.0,
DAT1.h to DAT1.0, DATA1.h to DATA1.0,
L H X H
DAT2.h to DAT2.0, DATA2.h to DATA2.0,
DAT3.h to DAT3.0 DATA3.h to DATA3.0
DAT0.1 to DAT0.h, DATA0.1 to DATA0.h,
DAT1.1 to DAT1.h, DATA1.1 to DATA1.h,
H L X L
DAT2.1 to DAT2.h, DATA2.1 to DATA2.h,
DAT3.1 to DAT3.h DATA3.1 to DATA3.h
DAT0.h to DAT0.1, DATA0.h to DATA0.1,
DAT1.h to DAT1.1, DATA1.h to DATA1.1,
H L X H
DAT2.h to DAT2.1, DATA2.h to DATA2.1,
DAT3.h to DAT3.1 DATA3.h to DATA3.1
CMD.h, CMD.0, and CMD.1 are Hi Z BS.h, BS.0, and BS.1 are Hi Z (isolation
H H X X
(isolation mode). mode).
L L H X CMD.h to CMD.0 and CMD.1 BS.h to BS.0 and BS.1
L L L X CMD.0 and CMD.1 to CMD.h BS.0 and BS.1 to BS.h
Command
L H H X CMD.h to CMD.0 BS.h to BS.0
L H L X CMD.0 to CMD.h BS.0 to BS.h
H L H X CMD.h to CMD.1 BS.h to BS.1
H L L X CMD.1 to CMD.h BS.1 to BS.h
DAT1.0 and DAT1.1 to IRQ. DATA1.0 and DATA1.1 to IRQ.
H H X X
IRQ is an open-drain output. IRQ is an open-drain output.
DAT1.1 to IRQ. DATA1.1 to IRQ.
L H X X
Interrupt
IRQ is an open-drain output. IRQ is an open-drain output.
request
DAT1.0 to IRQ. DATA1.0 to IRQ.
H L X X
IRQ is an open-drain output. IRQ is an open-drain output.
L L X X IRQ is Hi Z. IRQ is Hi Z.
(1) Broadcast mode in which the host writes to or reads from both cards in parallel
16
Submit Documentation Feedback