Datasheet

SN65LVDS4
SLLSE15 –JULY 2011 www.ti.com
RECEIVER ELECTRICAL CHARACTERISTICS
over recommended operating conditions, V
CC
= 2.5 V, V
ID
= 150 mV–600 mV, V
CM
= V
ID
/2 to V
CC
– V
ID
/2 V, 10 pF load
(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN
(1)
TYP
(2)
MAX UNIT
V
ITH+
Positive-going differential input voltage threshold 50
See Figure 1, V
CC1.8
, V
CC2.5
mV
V
ITH–
Negative-going differential input voltage threshold –50
V
DD
= 3.3V, I
OH
= –8 mA V
DD
– 0.25
V
OH
High-level output voltage V
DD
= 2.5V, I
OH
= –6 mA V
DD
– 0.25 V
V
DD
= 1.8 V, I
OH
= –4 mA V
DD
– 0.25
V
DD
= 3.3 V, I
OL
= 8 mA 0.25
V
OL
Low-level output voltage V
DD
= 2.5 V, I
OL
= 6 mA 0.25 V
V
DD
= 1.8 V, I
OL
= 4 mA 0.25
No load, steady state, V
DD
= 3.3 V, V
ID
+ 22 28
P
static
Static power mW
No load, steady state, V
DD
= 2.5 V, V
ID
+ 20 25
C
I
Input capacitance V
I
= 0.4 sin(4E6πt) + 0.5 V 4 pF
C
O
Output capacitance V
I
= 0.4 sin(4E6πt) + 0.5 V 4 pF
(1) The algebraic convention, in which the least positive (most negative) limit is designated as a minimum, is used in this data sheet.
(2) All typical values are at 25°C .
RECEIVER ELECTRICAL CHARACTERISTICS
over recommended operating conditions, V
CC
= 1.8 V, V
ID
= 150 mV–600 mV, V
CM
= V
ID
/2 to V
CC
– V
ID
/2 V, 10 pF load
(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN
(1)
TYP
(2)
MAX UNIT
V
ITH+
Positive-going differential input voltage threshold 50
See Figure 1, V
CC1.8
, V
CC2.5
mV
V
ITH–
Negative-going differential input voltage threshold –50
V
DD
= 3.3V, I
OH
= –8 mA V
DD
– 0.25
V
OH
High-level output voltage V
DD
= 2.5V, I
OH
= –6 mA V
DD
– 0.25 V
V
DD
= 1.8 V, I
OH
= –4 mA V
DD
– 0.25
V
DD
= 3.3 V, I
OL
= 8 mA 0.25
V
OL
Low-level output voltage V
DD
= 2.5 V, I
OL
= 6 mA 0.25 V
V
DD
= 1.8 V, I
OL
= 4 mA 0.25
No load, steady state, V
DD
= 3.3 V, V
ID
+ 18 21
P
static
Static power No load, steady state, V
DD
= 2.5 V, V
ID
+ 16 19 mW
No load, steady state, V
DD
= 1.8 V, V
ID
+ 13 16
C
I
Input capacitance V
I
= 0.4 sin(4E6πt) + 0.5 V 4 pF
C
O
Output capacitance V
I
= 0.4 sin(4E6πt) + 0.5 V 4 pF
(1) The algebraic convention, in which the least positive (most negative) limit is designated as a minimum, is used in this data sheet.
(2) All typical values are at 25°C .
4 Copyright © 2011, Texas Instruments Incorporated