Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - transceivers LVDS 1/1 TSSOP 14

SN65LVDS180-Q1

SN65LVDS050-Q1

SN65LVDS051-Q1

www.ti.com

SGLS204C –SEPTEMBER 2003–REVISED MARCH 2013

HIGH-SPEED DIFFERENTIAL LINE DRIVERS AND RECEIVERS

Check for Samples: SN65LVDS180-Q1, SN65LVDS050-Q1, SN65LVDS051-Q1

FEATURES

• Qualified for Automotive Applications

• ESD Protection Exceeds 2000 V Per MIL-STD-

883, Method 3015; Exceeds 200 V Using

Machine Model (C = 200 pF, R = 0)

• Meets or Exceeds the Requirements of ANSI

TIA/EIA-644-1995 Standard

• Signaling Rates up to 400 Mbps

• Bus-Terminal ESD Exceeds 12 kV

• Operates From a Single 3.3-V Supply

• Low-Voltage Differential Signaling With Typical

Output Voltages of 350 mV and a 100-Ω Load

• Propagation Delay Times

– Driver: 1.7 ns Typ

– Receiver: 3.7 ns Typ

• Power Dissipation at 200 MHz

– Driver: 25 mW Typical

– Receiver: 60 mW Typical

• LVTTL Input Levels Are 5-V Tolerant

• Receiver Maintains High Input Impedance With

< 1.5 V

• Receiver Has Open-Circuit Fail Safe

DESCRIPTION

The SN65LVDS180, SN65LVDS050, and

SN65LVDS051 are differential line drivers and

receivers that use low-voltage differential signaling

(LVDS) to achieve signaling rates as high as 400

Mbps. The TIA/EIA-644 standard compliant electrical

interface provides a minimum differential output

voltage magnitude of 247 mV into a 100-Ω load and

receipt of 50-mV signals with up to 1 V of ground

potential difference between a transmitter and

receiver.

The intended application of this device and signaling

technique is for point-to-point baseband data

transmission over controlled impedance media of

approximately 100-Ω characteristic impedance. The

transmission media may be printed-circuit board

traces, backplanes, or cables. (Note: The ultimate

rate and distance of data transfer is dependent upon

the attenuation characteristics of the media, the noise

coupling to the environment, and other application

specific characteristics).

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (29 pages)

PAGE 1
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.
PAGE 2
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION (CONTINUED) The devices offer various driver, receiver, and enabling combinations in industry standard footprints.
PAGE 3
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.
PAGE 4
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) UNIT VCC Supply voltage range (2) –0.5 V to 4 V Voltage range |VOD| D, R, DE, RE –0.5 V to 6 V Y, Z, A, and B –0.
PAGE 5
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 DEVICE ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) MIN TYP (1) MAX Driver and receiver enabled, no receiver load, driver RL = 100 Ω 9 12 Driver enabled, receiver disabled, RL = 100 Ω 5 7 Driver disabled, receiver enabled, no load 1.5 2 Disabled 0.
PAGE 6
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com RECEIVER ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER VIT+ Positive-going differential input voltage threshold VIT- Negative-going differential input voltage threshold VOH High-level output voltage VOL Low-level output voltage TEST CONDITIONS See Figure 5 and MIN TYP (1) MAX 50 –50 IOH = -8 mA 2.4 IOH = -4 mA 2.8 mV V IOL = 8 mA 0.
PAGE 7
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 PARAMETER MEASUREMENT INFORMATION DRIVER IOY Driver Enable Y II A IOZ VOD V VOY Z VI OY )V OZ 2 VOC VOZ Figure 1. Driver Voltage and Current Definitions Driver Enable Y 100 Ω ±1% VOD Input Z CL = 10 pF (2 Places) 2V 1.4 V 0.8 V Input tPHL tPLH 100% 80% VOD(H) Output 0V VOD(L) 20% 0% tf A.
PAGE 8
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) A. All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns. CL includes instrumentation and fixture capacitance within 0,06 mm of the D.U.T. The measurement of VOC(PP) is made on test equipment with a –3-dB bandwidth of at least 300 MHz. Figure 3.
PAGE 9
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 PARAMETER MEASUREMENT INFORMATION (continued) RECEIVER A V IA )V IB VID 2 R VIA B VIC VO VIB Figure 5. Receiver Voltage Definitions Receiver Minimum and Maximum Input Threshold Test Voltages APPLIED VOLTAGES (V) RESULTING DIFFERENTIAL INPUT VOLTAGE (mV) RESULTING COMMONMODE INPUT VOLTAGE (V) VIA VIB VID VIC 1.25 1.15 100 1.2 1.15 1.25 –100 1.2 2.4 2.3 100 2.35 2.3 2.
PAGE 10
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 A. www.ti.com All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 ± 0.2 ns. CL includes instrumentation and fixture capacitance within 0,06 m of the D.U.T. Figure 6.
PAGE 11
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 Figure 7.
PAGE 12
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com TYPICAL CHARACTERISTICS DISABLED DRIVER OUTPUT CURRENT vs OUTPUT VOLTAGE Disabled Driver Output Current − mA 40 VCC = 3.3 V TA = 25°C DE = 0 V 30 Other output at 0 V 20 Other output at 1.2 V 10 VOZ = VOY 0 −10 Other output at 2.4 V −20 −30 0 0.5 1 1.5 2 VO − Output Voltage − V Figure 8. DRIVER LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 3.5 VCC = 3.
PAGE 13
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 TYPICAL CHARACTERISTICS (continued) RECEIVER LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT RECEIVER HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 5 4 VCC = 3.3 V TA = 25°C VOH − High-Level Output Voltage − V VOL − Low-Level Output Votlage − V VCC = 3.3 V TA = 25°C 4 3 2 1 0 0 10 20 30 40 50 IOL − Low-Level Output Current − mA Figure 11. VCC = 3 V VCC = 3.6 V 1.
PAGE 14
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) t PLH − High-To-Low Level Propagation Delay Time − ms RECEIVER HIGH-TO-LOW LEVEL PROPAGATION DELAY TIME vs FREE-AIR TEMPERATURE 4.5 VCC = 3.3 V 4 VCC = 3 V 3.5 VCC = 3.6 V 3 2.5 −50 −30 10 −10 50 30 70 TA − Free−Air Temperature − °C Figure 15.
PAGE 15
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 APPLICATION INFORMATION The devices are generally used as building blocks for high-speed point-to-point data transmission. Ground differences are less than 1 V with a low common-mode output and balanced interface for low noise emissions. Devices can interoperate with RS-422, PECL, and IEEE-P1596. Drivers/receivers maintain ECL speeds without the power and dual supply requirements.
PAGE 16
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 www.ti.com It is only under these conditions that the output of the receiver will be valid with less than a 100-mV differential input voltage magnitude. The presence of the termination resistor, Rt, does not affect the fail-safe function as long as it is connected as shown in the figure.
PAGE 17
SN65LVDS180-Q1 SN65LVDS050-Q1 SN65LVDS051-Q1 www.ti.com SGLS204C – SEPTEMBER 2003 – REVISED MARCH 2013 REVISION HISTORY Changes from Original (September 2003) to Revision A Page • Deleted Feature: "Qualification in Accordance With AEC-Q100†" ....................................................................................... 1 • Deleted Feature: "Customer-Specific Configuration Control..." ............................................................................................
PAGE 18
PACKAGE OPTION ADDENDUM www.ti.
PAGE 19
PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.
PAGE 20
PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SN65LVDS051PWRG4Q1 TSSOP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 SN65LVDS180PWRG4Q1 TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 PW 14 2000 330.0 12.
PAGE 21
PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65LVDS051PWRG4Q1 TSSOP PW 16 2000 367.0 367.0 35.0 SN65LVDS051PWRQ1 TSSOP PW 16 2000 367.0 367.0 35.0 SN65LVDS180PWRG4Q1 TSSOP PW 14 2000 367.0 367.0 35.0 SN65LVDS180PWRQ1 TSSOP PW 14 2000 367.0 367.0 35.
PAGE 22
PAGE 23
PAGE 24
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.