Datasheet

www.ti.com
ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING CONDITIONS
2.4 

V
ID

2

V
ID

2
ELECTRICAL CHARACTERISTICS
SN65LV1021
SN65LV1212
SLLS526G – FEBRUARY 2002 – REVISED DECEMBER 2005
over operating free-air temperature range (unless otherwise noted)
(1)
UNIT
V
CC
to GND -0.3 V to 4 V
LVTTL input voltage -0.3 V to (V
CC
+ 0.3 V)
LVTTL output voltage -0.3 V to (V
CC
+ 0.3 V)
LVDS receiver input voltage -0.3 V to 3.9 V
LVDS driver output voltage -0.3 V to 3.9 V
LVDS output short circuit duration Continuous
Electrostatic discharge: HBM up to 6 kV
MM up to 200 V
Junction temperature 150°C
Storage temperature -65°C to 150°C
Lead temperature (soldering, 4 seconds) 260°C
T
A
= 25°C Maximum package power dissipation 1.27 W
Package derating 10.3 mW/°C above 25°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
MIN NOM MAX UNIT
V
CC
(1)
Supply voltage 3 3.3 3.6 V
Receiver input voltage range 0 2.4 V
V
CM
Receiver input common mode range V
Supply noise voltage 100 mV
P-P
T
A
Operating free-air temperature -40 25 85 °C
(1) By design, DVCC and AVCC are separated internally and does not matter what the difference is for XDVCC-AVCCX, as long as both
are within 3 V to 3.6 V.
over recommended operating supply and temperature ranges (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SERIALIZER LVCMOS/LVTTL DC SPECIFICATIONS (see Note
(1)
)
V
IH
High-level input voltage 2 V
CC
V
V
IL
Low-level input voltage GND 0.8 V
V
CL
Input clamp voltage I
CL
= -18 mA -1.5 V
I
IN
Input current (see Note
(2)
) V
IN
= 0 V or 3.6 V -200 ±100 200 µA
DESERIALIZER LVCMOS/LVTTL DC SPECIFICATIONS (see Note
(3)
)
V
IH
High-level input voltage 2 V
CC
V
V
IL
Low-level input voltage GND 0.8 V
V
CL
Input clamp voltage I
CL
= -18 mA -0.62 -1.5 V
I
IN
Input current V
IN
= 0 V or 3.6 V -200 200 µA
V
OH
High-level output voltage I
OH
= -5 mA 2.2 3 V
CC
V
V
OL
Low-level output voltage I
OL
= 5 mA GND 0.25 0.5 V
I
OS
Output short-circuit current V
OUT
= 0 V -15 -47 -85 mA
(1) Apply to D
IN0
-D
IN9
, TCLK, PWRDN, TCLK_R/ F, SYNC1, SYNC2, DEN
(2) High I
IN
values are due to pull-up and pull-down resistors on the inputs.
(3) Apply to input pins PWRDN, RCLK_R/ F, REN, REFCLK; apply to output pins R
OUTx
, RCLK, LOCK
7