Datasheet

SN65HVD230
SN65HVD231
SN65HVD232
SLOS346K –MARCH 2001– REVISED FEBRUARY 2011 www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION
The SN65HVD230, SN65HVD231, and SN65HVD232 controller area network (CAN) transceivers are designed
for use with the Texas Instruments TMS320Lx240x™ ; 3.3-V DSPs with CAN controllers, or with
equivalent devices. They are intended for use in applications employing the CAN serial communication physical
layer in accordance with the ISO 11898 standard. Each CAN transceiver is designed to provide differential
transmit capability to the bus and differential receive capability to a CAN controller at speeds up to 1 Mbps.
Designed for operation in especially-harsh environments, these devices feature cross-wire protection,
loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range.
The transceiver interfaces the single-ended CAN controller with the differential CAN bus found in industrial,
building automation, and automotive applications. It operates over a -2-V to 7-V common-mode range on the
bus, and it can withstand common-mode transients of ±25 V.
On the SN65HVD230 and SN65HVD231, pin 8 provides three different modes of operation: high-speed, slope
control, and low-power modes. The high-speed mode of operation is selected by connecting pin 8 to ground,
allowing the transmitter output transistors to switch on and off as fast as possible with no limitation on the rise
and fall slopes. The rise and fall slopes can be adjusted by connecting a resistor to ground at pin 8, since the
slope is proportional to the pin's output current. This slope control is implemented with external resistor values of
10 kΩ, to achieve a 15-V/μs slew rate, to 100 kΩ, to achieve a 2-V/μs slew rate. See the Application Information
section of this data sheet.
The circuit of the SN65HVD230 enters a low-current standby mode during which the driver is switched off and
the receiver remains active if a high logic level is applied to pin 8. The DSP controller reverses this low-current
standby mode when a dominant state (bus differential voltage > 900 mV typical) occurs on the bus.
The unique difference between the SN65HVD230 and the SN65HVD231 is that both the driver and the receiver
are switched off in the SN65HVD231 when a high logic level is applied to pin 8 and remain in this sleep mode
until the circuit is reactivated by a low logic level on pin 8.
The V
ref
pin 5 on the SN65HVD230 and SN65HVD231 is available as a V
CC
/2 voltage reference.
The SN65HVD232 is a basic CAN transceiver with no added options; pins 5 and 8 are NC, no connection.
Table 1. AVAILABLE OPTIONS
(1)
INTEGRATED SLOPE
PART NUMBER LOW POWER MODE V
ref
PIN T
A
MARKED AS:
CONTROL
SN65HVD230 Standby mode Yes Yes VP230
SN65HVD231 Sleep mode Yes Yes VP231
40°C to 85°C
No standby or sleep
SN65HVD232 No No VP232
mode
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
FUNCTION TABLES
DRIVER (SN65HVD230, SN65HVD231)
(1)
OUTPUTS
INPUT D R
S
BUS STATE
CANH CANL
L H L Dominant
V
(Rs)
< 1.2 V
H Z Z Recessive
Open X Z Z Recessive
X V
(Rs)
> 0.75 V
CC
Z Z Recessive
(1) H = high level; L = low level; X = irrelevant; ? = indeterminate; Z = high impedance
2 Submit Documentation Feedback © 2001–2011, Texas Instruments Incorporated
Product Folder Link(s): SN65HVD230 SN65HVD231 SN65HVD232