Datasheet
SN65HVD10, SN65HVD10Q, SN75HVD10
SN65HVD11, SN65HVD11Q, SN75HVD11
SN65HVD12, SN75HVD12
www.ti.com
SLLS505M –FEBRUARY 2002–REVISED JULY 2013
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range unless otherwise noted
MIN NOM MAX UNIT
V
CC
Supply voltage 3 3.6
V
I
or V
IC
Voltage at any bus terminal (separately or common mode) –7
(1)
12
V
IH
High-level input voltage D, DE, RE 2 V
CC
V
V
IL
Low-level input voltage D, DE, RE 0 0.8
V
ID
Differential input voltage Figure 7 –12 12
Driver –60
I
OH
High-level output current mA
Receiver –8
Driver 60
I
OL
Low-level output current mA
Receiver 8
R
L
Differential load resistance 54 60 Ω
C
L
Differential load capacitance 50 pF
HVD10 32
Signaling rate HVD11 10 Mbps
HVD12 1
T
J
(2)
Junction temperature 145 °C
(1) The algebraic convention, in which the least positive (most negative) limit is designated as minimum is used in this data sheet.
(2) See thermal characteristics table for information regarding this specification.
DRIVER ELECTRICAL CHARACTERISTICS
over recommended operating conditions unless otherwise noted
PARAMETER TEST CONDITIONS MIN TYP
(1)
MAX UNIT
V
IK
Input clamp voltage I
I
= –18 mA –1.5 V
I
O
= 0 2 V
CC
|V
OD
| Differential output voltage
(2)
R
L
= 54 Ω, See Figure 1 1.5 V
V
test
= –7 V to 12 V, See Figure 2 1.5
Change in magnitude of differential output
Δ|V
OD
| See Figure 1 and Figure 2 –0.2 0.2 V
voltage
V
OC(PP)
Peak-to-peak common-mode output voltage 400 mV
V
OC(SS)
Steady-state common-mode output voltage 1.4 2.5 V
See Figure 3
Change in steady-state common-mode output –0.0
ΔV
OC(SS)
0.05 V
voltage 5
I
OZ
High-impedance output current See receiver input currents
D –100 0
I
I
Input current μA
DE 0 100
I
OS
Short-circuit output current –7 V ≤ V
O
≤ 12 V –250 250 mA
C
(OD)
Differential output capacitance V
OD
= 0.4 sin (4E6πt) + 0.5 V, DE at 0 V 16 pF
RE at V
CC
,
Receiver disabled and
D & DE at V
CC,
9 15.5 mA
driver enabled
No load
RE at V
CC
,
D at V
CC
, Receiver disabled and
I
CC
Supply current 1 5 μA
DE at 0 V, driver disabled (standby)
No load
RE at 0 V,
Receiver enabled and
D & DE at V
CC
, 9 15.5 mA
driver enabled
No load
(1) All typical values are at 25°C and with a 3.3-V supply.
(2) For T
A
> 85°C, V
CC
is ±5%.
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: SN65HVD10 SN65HVD10Q SN75HVD10 SN65HVD11 SN65HVD11Q SN75HVD11
SN65HVD12 SN75HVD12