Datasheet
ABSOLUTE MAXIMUM RATINGS
(1)
RECOMMENDED OPERATING CONDITIONS
SUPPLY CURRRENT
DEVICE SWITCHING CHARACTERISTICS
SN65HVD1040
www.ti.com
............................................................................................................................................... SLLS631D – MARCH 2007 – REVISED DECEMBER 2008
VALUE
V
CC
Supply voltage
(2)
– 0.3 V to 7 V
V
I(bus)
Voltage range at any bus terminal (CANH, CANL, SPLIT) – 27 V to 40 V
I
O(OUT)
Receiver output current -20 mA to 20 mA
Voltage input, transient pulse
(3)
, (CANH, CANL, SPLIT) – 200 V to 200 V
IEC Contact Discharge (IEC 61000-4-2) Bus terminals vs GND ± 6 kV
Bus terminals vs GND ± 12 kV
JEDEC Standard 22,
Human body model
Test Method A114-C.01
All pins ± 4 kV
ESD
Field-Induced-Charged JEDEC Standard 22,
All pins ± 1 kV
Device Model Test Method C101
Machine model ANSI/ESDS5.2-1996 ± 200 V
IEC Bus terminals vs GND ± 6 kV
V
I
Voltage input range (TXD, STB) – 0.5 V to 6 V
T
J
Junction temperature – 55 ° C to 170 ° C
(1) Stresses beyond those listed under " absolute maximum ratings " may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under " recommended operating
conditions " is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.
(3) Tested in accordance with ISO 7637, test pulses 1, 2, 3a, 3b, 5, 6 & 7.
MIN NOM MAX UNIT
V
CC
Supply voltage 4.75 5.25 V
V
I
or V
IC
Voltage at any bus terminal (separately or common mode) – 12
(1)
12 V
V
IH
High-level input voltage 2 5.25 V
TXD, STB
V
IL
Low-level input voltage 0 0.8 V
V
ID
Differential input voltage – 6 6 V
Driver – 70
I
OH
High-level output current mA
Receiver – 2
Driver 70
I
OL
Low-level output current mA
Receiver 2
t
SS
Maximum pulse width to remain in standby 0.7 µ s
T
J
Junction temperature – 40 150 ＝ C
(1) The algebraic convention, in which the least positive (most negative) limit is designated as minimum is used in this data sheet.
over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Dominant V
I
= 0 V, 60 Ω Load, STB at 0 V 50 70
mA
I
CC
Supply current, V
CC
Recessive V
I
= V
CC
, STB at 0 V 6 10
Standby STB at VCC, VI = VCC 5 12 µ A
over recommended operating conditiions (unless otherwise noted)
TEST MIN TYP MAX UNIT
PARAMETER
CONDITIONS
t
loop1
Total loop delay, driver input to receiver output, Recessive to Dominant 90 230
STB at 0 V,
ns
See Figure 9
t
loop2
Total loop delay, driver input to receiver output, Dominant to Recessive 90 230
Copyright © 2007 – 2008, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): SN65HVD1040