Datasheet

www.ti.com EVM Setup and Precautions
Table 2. Status LEDs
LED NAME FUNCTION
D2 CQ ON – CQ voltage present
OFF – No CQ voltage present
D3 EN ON – Transmitter enabled
OFF – Transmitter disabled
D4 TX ON - TX voltage greater than 2V
OFF – TX voltage less than 2V
D5 RX ON - RX voltage greater than 2V
OFF – RX voltage less than 2V
D6 VCC_IN ON – VCC_IN voltage greater than 2V
OFF – VCC_IN voltage less than 2V
D7 VCC_SET ON – Vcc =3.3V
OFF – Vcc = 5V
D8 WAKE ON – WAKE notification from the PHY to the local controller
OFF – No WAKE event
D9 CUR_WARN ON – CQ over-current fault
OFF – CQ current OK
D10 TEMP_WARN ON – Internal temperature approaching thermal shutdown
OFF – Internal temperature OK
D11 PWR_WARN ON – Power Fail. Lp and Vcc voltages are not at correct levels
OFF – Power OK, Lp and Vcc voltages are at correct levels
Table 3. Bill Of Materials
Item Qty Reference Part Footprint Mfr Part Number Notes
1 1 C1 10uF 805 Taiyo Yuden EMK212BJ106KG-T
2 1 C2 1uF TDK C1608X7R1C105K
3 1 C3 0.1uF Murata GRM188R71H104K
A93D
4 1 C4 3.3uF TDK C3216X7R1H335K
5 1 C5 DNI DNI NA
6 6 D2,D3,D4,D5,D6,D7 GREEN Lumex Opto SML-LXT0805GW-
TR
7 1 D8 WHITE Panasonic- SSG LNJ037X8ARA
8 3 D9,D10,D11 YELLOW Lumex Opto SML-LXT0805YW-
TR
9 1 JMP1 Header 2x3 HDR_THVT_2x Samtec HTSW-103-07-G-D Shunt pins
3_100 1-2
10 2 JMP2 Header 1x3 HDR_THVT_1X Samtec HTSW-103-07-G-S Shunt pins
3_100 1-2
11 4 JMP3, JMP4, JMP5 Header 1x3 HDR_THVT_1X Samtec HTSW-103-07-G-S
3_100
12 1 JMP8 Header 1x2 HDR_THVT_1X Samtec HTSW-102-07-G-D Shunt pins
2_100 1-2
13 1 JMP9 Header 2x9 HDR_THVT_2x Samtec HTSW-109-07-G-D
9_100
14 1 R1 10k ohm 603 Yageo RC0603FR-0710KL
15 9 R2,R3,R4,R5,R6,R7,R8, 3.5k ohm 603 Panasonic-ECG ERJ-3EKF3571V
R9,R10
16 1 R11 20k ohm 1206 Panasonic-ECG ERJ-8ENF2002V
17 1 R12 0 ohm 1210 KOA Speer RK73Z2ETTE
18 2 TB1, TB2 Terminal TB_THRTSCR_ Phoenix Contact 1725669
Block 1x3 1x3_100
5
SLLU178–February 2013 SN65HVD101 and SN65HVD102 EVM User's Guide
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated