Datasheet

REG104
3
SBVS025G
REG104GA
REG104FA
PARAMETER CONDITION MIN TYP MAX UNITS
OUTPUT VOLTAGE
Output Voltage Range V
OUT
REG104-2.5 2.5 V
REG104-2.7 2.7 V
REG104-3.0 3.0 V
REG104-3.3 3.3 V
REG104-5 5V
REG104-A V
REF
5.5 V
Reference Voltage V
REF
1.295 V
Adjust Pin Current I
ADJ
0.2 1 µA
Accuracy ±0.5 ±2%
T
J
= –40°C to +85°C ±3.0 %
vs Temperature dV
OUT
/dT T
J
= –40°C to +85°C70ppm/°C
vs Line and Load I
OUT
= 10mA to 1A, V
IN
= (V
OUT
+ 0.7V) to 15V ±0.5 ±2.5 %
T
J
= –40°C to +85°CV
IN
= (V
OUT
+ 0.9V) to 15V ±3.5 %
DC DROPOUT VOLTAGE
(2, 3)
V
DROP
I
OUT
= 10mA 3 25 mV
For all models except 5V I
OUT
= 1A 230 400 mV
For 5V model I
OUT
= 1A 320 500 mV
For all models except 5V I
OUT
= 1A 480 mV
T
J
= –40°C to +85°C
For 5V models I
OUT
= 1A 580 mV
T
J
= –40°C to +85°C
VOLTAGE NOISE
f = 10Hz to 100kHz V
n
Without C
NR
(all models) C
NR
= 0, C
OUT
= 0 35µV
RMS
/V • V
OUT
µV
RMS
With C
NR
(all fixed voltage models) C
NR
= 0.01µF, C
OUT
= 10µF10µV
RMS
/V • V
OUT
µV
RMS
OUTPUT CURRENT
Current Limit
(4)
I
CL
1.2 1.7 2.1 A
T
J
= –40°C to +85°C 1.0 2.2 A
RIPPLE REJECTION
f = 120Hz 65 dB
ENABLE CONTROL
V
ENABLE
High (output enabled) V
ENABLE
2V
IN
V
V
ENABLE
Low (output disabled) –0.2 0.5 V
I
ENABLE
High (output enabled) I
ENABLE
V
ENABLE
= 2V to V
IN
, V
IN
= 2.1V to 6.5
(5)
1 100 nA
I
ENABLE
Low (output disabled) V
ENABLE
= 0V to 0.5V 2 100 nA
Output Disable Time 50 µs
Output Enable Softstart Time 1.5 ms
THERMAL SHUTDOWN
Junction Temperature
Shutdown 150 °C
Reset from Shutdown 130 °C
GROUND PIN CURRENT
Ground Pin Current I
GND
I
OUT
= 10mA 0.5 0.7 mA
I
OUT
= 1A 1.7 1.8 mA
Enable Pin Low V
ENABLE
≤ 0.5V 0.5 µA
INPUT VOLTAGE V
IN
Operating Input Voltage Range
(6)
2.1 15 V
Specified Input Voltage Range V
IN
> 2.7V V
OUT
+ 0.7 15 V
T
J
= –40°C to +85°CV
IN
> 2.9V V
OUT
+ 0.9 15 V
TEMPERATURE RANGE
Specified Range T
J
–40 +85 °C
Operating Range –55 +125 °C
Storage Range –65 +150 °C
Thermal Resistance
DDPAK-5 Surface Mount
θ
JC
Junction-to-Case 4 °C/W
SOT223-5 Surface Mount
θ
JC
Junction-to-Case 15 °C/W
NOTES: (1) The REG104 does not require a minimum output capacitor for stability. However, transient response can be improved with proper capacitor selection.
(2) Dropout voltage is defined as the input voltage minus the output voltage that produces a 2% change in the output voltage from the value at V
IN
= V
OUT
+ 1V
at fixed load.
(3) Not applicable for V
OUT
less than 2.7V.
(4) Current limit is the output current that produces a 15% change in output voltage from V
IN
= V
OUT
+ 1V and I
OUT
= 10mA.
(5) For V
IN
> 6.5V, see typical characteristic V
ENABLE
vs I
ENABLE
.
(6) The REG104 no longer regulates when V
IN
< V
OUT
+ V
DROP (MAX)
. In drop-out or when the input voltage is between 2.7V and 2.1V, the impedance from V
IN
to V
OUT
is typically less than 1Ω at T
J
= +25°C. See typical characteristic Output Voltage Change vs V
IN
.
ELECTRICAL CHARACTERISTICS
Boldface limits apply over the specified temperature range, T
J
= –40°C to +85°C
At T
J
= +25°C, V
IN
= V
OUT
+ 1V (V
OUT
= 3.0V for REG104-A), V
ENABLE
= 2V, I
OUT
= 10mA, C
NR
= 0.01µF, and C
OUT
= 0.1µF
(1)
, unless otherwise noted.