Datasheet
Table Of Contents
- FEATURES
- APPLICATIONS
- DESCRIPTION
- ABSOLUTE MAXIMUM RATINGS
- ELECTRICAL CHARACTERISTICS
- ELECTRICAL CHARACTERISTICS
- DEVICE INFORMATION
- PTH12030W TYPICAL CHARACTERISTICS (VI = 12 V)Characteristic data has been developed from actual products tested at 25C. This data is considered typical data for the converter. Applies to , , and .SOA curves represent the conditions at which internal components are at or below the manufacturer’s maximum operating temperatures. Derating limits apply to modules soldered directly to a 4 in. 4 in. double-sided PCB with 1 oz. copper. For surface mount products (AS and AZ suffix), multiple vias (plated through holes) are required to add thermal paths around the power pins. Please refer to the mechanical specification for more information. Applies to .
- PTH12030L TYPICAL CHARACTERISTICS (VI = 12 V)Characteristic data has been developed from actual products tested at 25C. This data is considered typical data for the converter. Applies to , , and .SOA curves represent the conditions at which internal components are at or below the manufacturer’s maximum operating temperatures. Derating limits apply to modules soldered directly to a 4 in. 4 in. double-sided PCB with 1 oz. copper. For surface mount products (AS and AZ suffix), multiple vias (plated through holes) are required to add thermal paths around the power pins. Please refer to the mechanical specification for more information. Applies to .
- APPLICATION INFORMATION
- TAPE AND REEL SPECIFICATIONS
- TRAY SPECIFICATIONS
STANDARD APPLICATION
MarginDown
MarginUp
V
I
C
330 F
(Optional)
O
m
C
560 F
Electrolytic
(Required)
I
m
Inhibit
GND
GND
V
O
V Sense
O
Track
R
SET
PTH12030x
(TopView)
1
3
13
12 11
9
7
65
4
2
10
8
L
O
A
D
ABSOLUTE MAXIMUM RATINGS
PTH12030W/L
SLTS211H – MAY 2003 – REVISED DECEMBER 2008 ....................................................................................................................................................
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
A. R
SET
= Required to set the output voltage to a value higher than the minimum value. See the Application Information
section for values.
ORDERING INFORMATION
For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet, or see
the TI website at www.ti.com.
Over operating free-air temperature range, all voltages are with respect to GND (unless otherwise noted)
MIN TYP MAX UNIT
V
Track
Track pin voltage – 0.3 V
I
+ 0.3 V
T
A
Operating Temperature Over V
I
range – 40 85
Range
T
wave
Wave solder temperature Surface temperature of module body or pins PTH12030WAH
260
(5seconds maximum)
PTH12030WAD
° C
PTH12030WAS 235
(1)
T
reflow
Solder reflow temperature Surface temperature of module body or pins
PTH12030WAZ 260
(1)
T
stg
Storage Temperature Storage temperature of module removed from shipping package – 55 125
T
pkg
Packaging temperature Shipping Tray or Tape and Reel storage or bake temperature 45
Mechanical Shock Per Mil-STD-883D, Method 2002.3, 1 ms, 1/2 Sine, mounted 500 G
Mechanical Vibration Mil-STD-883D, Method 2007.2 20-2000 Hz 15 G
Weight 10 grams
Flammability Meets UL 94V-O
(1) During soldering of package version, do not elevate peak temperature of the module, pins, or internal components above the stated
maximum.
2 Submit Documentation Feedback Copyright © 2003 – 2008, Texas Instruments Incorporated
Product Folder Link(s): PTH12030W/L