Datasheet

OPA699
3
SBOS261D
www.ti.com
OPA699ID
0 ° C to –40 ° C to MIN/ TEST
PARAMETER CONDITIONS +25°C +25°C
(1)
70°C
(2)
+85°C
(2)
UNITS MAX LEVEL
(3)
AC PERFORMANCE (see Figure 1)
Small Signal Bandwidth (V
O
< 0.5V
PP
) G = [phone] MHz min B
G = +12 86 MHz typ C
G = –6 269 MHz typ C
Gain Bandwidth Product (G ≥ +20) V
O
< 0.5V
PP
, G = [phone] MHz min B
Gain Peaking V
O
< 0.5V
PP
, G = +4 7.5 dB typ C
0.1dB Gain Flatness Bandwidth V
O
< 0.5V
PP
30 MHz typ C
Large-Signal Bandwidth V
O
= 4V
PP
290 190 180 170 MHz min B
Step Response
Slew Rate 4V Step 1400 1300 1200 1100 V/µsminB
Rise-and-Fall Time 0.5V Step 1.6 1.65 1.8 2 ns max B
Settling Time: 0.05% 2V Step 8 ns typ C
Spurious-Free Dynamic Range, Even f = 5MHz, V
O
= 2V
PP
67 64 62 60 dB min B
Odd f = 5MHz, V
O
= 2V
PP
87 85 84 80 dB min B
Differential Gain NTSC, PAL, R
L
= 500Ω 0.012 % typ C
Differential Phase NTSC, PAL, R
L
= 500Ω 0.008 ° typ C
Input Noise Density
Voltage Noise f ≥ 1MHz 4.1 4.6 5.2 5.5 nV/√Hz max B
Current Noise f ≥ 1MHz 2.0 2.5 2.7 2.9 pA/√Hz max B
DC PERFORMANCE (V
CM
= 0V)
Open-Loop Voltage Gain (A
OL
)V
O
= ±0.5V 66 58 56 55 dB min A
Input Offset Voltage ±1.5
±5.0 ±6 ±7mVmaxA
Average Drift — ±15 ±20 µV/°CmaxB
Input Bias Current
(4)
+3 ±10 ±11 ±12 µAmaxA
Average Drift — ±15 ±20 nA/°CmaxB
Input Offset Current ±0.3
±2 ±2.5 ±3 µAmaxA
Average Drift — ±10 ±10 nA/°CmaxB
INPUT
Common-Mode Rejection Ratio Input Referred, V
CM
= ±0.5V 61 55 54 52 dB min A
Common-Mode Input Range
(5)
±3.3 ±3.2 ±3.2 ±3.1 V min A
Input Impedance
Differential-Mode 0.32 || 1 MΩ || pF typ C
Common-Mode 3.5 || 1 MΩ || pF typ C
OUTPUT V
H
= –V
L
= 4.3V
Output Voltage Range R
L
≥ 500Ω±4.1 ±3.9 ±3.9 ±3.8 V min A
Current Output, Sourcing +120 +90 +85 +80 mA min A
Sinking –120 –90 –85 –80 mA min A
Closed-Loop Output Impedance G = +4, f < 100kHz 0.8 Ω typ C
POWER SUPPLY
Operating Voltage, Specified ±5 V typ C
Maximum —
±6 ±6 ±6VmaxA
Quiescent Current, Maximum V
S
= ±5V 15.5 15.9 16.3 16.6 mA max A
Minimum V
S
= ±5V 15.5 15.2 14.9 14.6 mA min A
Power-Supply Rejection Ratio +V
S
= 4.5V to 5.5V
+PSRR (Input Referred) 75 68 67 66 dB min A
TYP MIN/MAX OVER TEMPERATURE
NOTES: (1) Junction temperature = ambient temperature for low temperature limit and +25°C Test Level A specifications. Junction temperature = ambient
temperature + 23°C at high temperature limit Test Level A specifications.
(2) Junction temperature = ambient at low temperature limit; junction temperature = ambient +1°C at high temperature limit for over-temperature
tested specifications.
(3) Test Levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value for information only.
(4) Current is considered positive out-of-node.
(5) CMIR tested as < 3dB degradation from minimum CMRR at specified limits.
(6) I
VH
(V
H
bias current) is positive, and I
VL
(V
L
bias current) is negative, under these conditions. See Note 3 and Figures 1 and 12.
(7) Limiter feedthrough is the ratio of the output magnitude to the sinewave added to V
H
(or V
L
) when V
IN
= 0.
ELECTRICAL CHARACTERISTICS: V
S
= ±5V
Boldface limits are tested at +25°C.
G = +6, R
F
= 750Ω, R
L
= 500Ω, and V
H
= –V
L
= 2V, (see Figure 1 for AC performance only), unless otherwise noted.