Datasheet
OPA342, 2342, 4342
3
SBOS106A
PACKAGE SPECIFIED
DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT
PRODUCT PACKAGE NUMBER RANGE MARKING NUMBER
(1)
MEDIA
OPA342NA SOT23-5 331 –40°C to +85°C B42 OPA342NA/250 Tape and Reel
"""""OPA342NA/3K Tape and Reel
OPA342UA SO-8 182 –40°C to +85°C OPA342UA OPA342UA Rails
"""""OPA342UA/2K5 Tape and Reel
OPA2342EA MSOP-8 337 –40°C to +85°C C42 OPA2342EA/250 Tape and Reel
"""""OPA2342EA/2K5 Tape and Reel
OPA2342UA SO-8 182 –40°C to +85°C OPA2342UA OPA2342UA Rails
"""""OPA2342UA/2K5 Tape and Reel
OPA4342EA TSSOP-14 357 –40°C to +85°C OPA4342EA OPA4342EA/250 Tape and Reel
"""""OPA4342EA/2K5 Tape and Reel
OPA4342UA SO-14 235 –40°C to +85°C OPA4342UA OPA4342UA Rails
"""""OPA4342UA/2K5 Tape and Reel
OPA4342PA DIP-14 010 –40°C to +85°C OPA4342PA OPA4342PA Rails
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /3K indicates 3000 devices per reel). Ordering 3000 pieces
of “OPA342NA/3K” will get a single 3000-piece Tape and Reel.
PACKAGE/ORDERING INFORMATION
Supply Voltage, V+ to V- ................................................................... 7.5V
Signal Input Terminals, Voltage
(2)
.....................(V–) –0.5V to (V+) +0.5V
Current
(2)
.................................................... 10mA
Output Short-Circuit
(3)
.............................................................. Continuous
Operating Temperature ..................................................–55°C to +125°C
Storage Temperature ..................................................... –65°C to +150°C
Junction Temperature ...................................................................... 150°C
Lead Temperature (soldering, 10s) ................................................. 300°C
ESD Tolerance (Human Body Model) ............................................ 4000V
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only. Functional opera-
tion of the device at these conditions, or beyond the specified operating
conditions, is not implied. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.5V beyond the supply
rails should be current-limited to 10mA or less. (3) Short-circuit to ground,
one amplifier per package.
ABSOLUTE MAXIMUM RATINGS
(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
PIN CONFIGURATIONS
1
2
3
5
4
V+
–In
Out
V–
+In
OPA342
SOT23-5
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Out D
–In D
+In D
–V
+In C
–In C
Out C
Out A
–In A
+In A
+V
+In B
–In B
Out B
OPA4342
TSSOP-14, SO-14, DIP-14
AD
BC
1
2
3
4
8
7
6
5
V+
Out B
–In B
+In B
Out A
–In A
+In A
V–
OPA2342
SO-8, MSOP-8
A
B
1
2
3
4
8
7
6
5
NC
V+
Out
NC
NC
–In
+In
V–
OPA342
SO-8