Datasheet

OPA130, OPA2130, OPA4130
3
SBOS053A
www.ti.com
ELECTRICAL CHARACTERISTICS
At T
A
= +25°C, V
S
= ±15V, and R
L
= 10kΩ, unless otherwise noted.
OPA130PA, UA
OPA2130PA, UA
OPA4130PA, UA
PARAMETER CONDITION MIN TYP MAX UNITS
OFFSET VOLTAGE
Input Offset Voltage ±0.2 ±1mV
vs Temperature
(1)
Operating Temperature Range ±2 ±10 µV/°C
vs Power Supply V
S
= ±2.25V to ±18V 2 20 µV/V
Channel Separation (dual and quad) 0.3 µV/V
INPUT BIAS CURRENT
(2)
Input Bias Current V
CM
= 0V +5 ±20 pA
vs Temperature See Typical Characteristics
Input Offset Current V
CM
= 0V ±2 ±20 pA
NOISE
Input Voltage Noise
Noise Density, f = 10Hz 30 nV/√Hz
f = 100Hz 18 nV/√Hz
f = 1kHz 16 nV/√Hz
f = 10kHz 16 nV/√Hz
Current Noise Density, f = 1kHz 4fA/√Hz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range, Positive (V+)–2 (V+)–1.5 V
Negative (V–)+2 (V–)+1.2 V
Common-Mode Rejection V
CM
= –13V to +13V 90 105 dB
INPUT IMPEDANCE
Differential 10
13
|| 1 Ω || pF
Common-Mode V
CM
= –13V to +13V 10
13
|| 3 Ω || pF
OPEN-LOOP GAIN
Open-loop Voltage Gain V
O
= –13.8V to +13V 120 135 dB
R
L
= 2kΩ, V
O
= –13V to +12V 120 135 dB
FREQUENCY RESPONSE
Gain-Bandwidth Product 1 MHz
Slew Rate 2V/µs
Settling Time: 0.1% G = 1, 10V Step, C
L
= 100pF 5.5 µs
0.01% G = 1, 10V Step, C
L
= 100pF 7 µs
Overload Recovery Time G = 1, V
IN
= ±15V 2 µs
Total Harmonic Distortion + Noise 1kHz, G = 1, V
O
= 3.5Vrms 0.0003 %
OUTPUT
Voltage Output, Positive (V+)–2 (V+)–1.5 V
Negative (V–)+1.2 (V–)+1 V
Positive R
L
= 2kΩ (V+)–3 (V+)–2.5 V
Negative R
L
= 2kΩ (V–)+2 (V–)+1.5 V
Short-Circuit Current ±18 mA
Capacitive Load Drive (Stable Operation) 10 nF
POWER SUPPLY
Specified Operating Voltage ±15 V
Operating Voltage Range ±2.25 ±18 V
Quiescent Current (per amplifier) I
O
= 0 ±530 ±650 µA
TEMPERATURE RANGE
Operating Range –40 +85 °C
Storage –40 +125 °C
Thermal Resistance,
θ
JA
DIP-8 100 °C/W
SO-8 Surface-Mount 150 °C/W
DIP-14 80 °C/W
SO-14 Surface-Mount 110 °C/W
NOTES: (1) Ensured by wafer test. (2) High-speed test at T
J
= 25°C.