Datasheet

"#"$ %"#"
"#&
%"#&$ &"#&
SBOS279E − SEPTEMBER 2003 − REVISED MAY 2008
www.ti.com
2
PACKAGE/ORDERING INFORMATION
(1)
PRODUCT PACKAGE-LEAD
PACKAGE
DESIGNATOR
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
Shutdown
OPA373 SOT23-6 DBV −40°C to +125°C A75 OPA373AIDBVT Tape and Reel, 250
″ ″ ″ ″ ″ OPA373AIDBVR Tape and Reel, 3000
OPA373 SO-8 D −40°C to +125°C OPA373A OPA373AID Rails, 100
″ ″ ″ ″ ″ OPA373AIDR Tape and Reel, 2500
OPA2373 MSOP-10 DGS −40°C to +125°C AYO OPA2373AIDGST Tape and Reel, 250
″ ″ ″ ″ ″ OPA2373AIDGSR Tape and Reel, 2500
OPA2373 DFN-10 DRC −40°C to +125°C OCEQ OPA2373AIDRCT Tape and Reel, 250
″ ″ ″ ″ ″ OPA2373AIDRCR Tape and Reel, 3000
Non-Shutdown
OPA374 SOT23-5 DBV −40°C to +125°C A76 OPA374AIDBVT Tape and Reel, 250
″ ″ ″ ″ ″ OPA374AIDBVR Tape and Reel, 3000
OPA374 SO-8 D −40°C to +125°C OPA274A OPA374AID Rails, 100
″ ″ ″ ″ ″ OPA374AIDR Tape and Reel, 2500
OPA2374 SOT23-8 DCN −40°C to +125°C ATP OPA2374AIDCNT Tape and Reel, 250
″ ″ ″ ″ ″ OPA2374AIDCNR Tape and Reel, 3000
OPA2374 SO-8 D −40°C to +125°C OPA2374A OPA2374AID Rails, 100
″ ″ ″ ″ ″ OPA2374AIDR Tape and Reel, 2500
OPA4374 SO-14 D −40°C to +125°C OPA4374A OPA4374AID Rails, 58
″ ″ ″ ″ ″ OPA4374AIDR Tape and Reel, 2500
OPA4374 TSSOP-14 PW −40°C to +125°C OPA4374A OPA4374AIPWT Tape and Reel, 250
″ ″ ″ ″ ″ OPA4374AIPWR Tape and Reel, 2500
(1)
For the most current package and ordering information, see the Package Option Addendum located at the end of this datasheet.
ABSOLUTE MAXIMUM RATINGS
(1)
Supply Voltage +7.0V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Input Terminals, Voltage
(2)
−0.5V to (V+) + 0.5V. . . . . . . . .
Current
(2)
±10mA. . . . . . . . . . . . . . . . . . .
Output Short-Circuit
(3)
Continuous. . . . . . . . . . . . . . . . . . . . . . . . .
Operating Temperature −55°C to +150°C. . . . . . . . . . . . . . . . . . . . .
Storage Temperature −65°C to +150°C. . . . . . . . . . . . . . . . . . . . . . .
Junction Temperature +150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead Temperature (soldering, 10s) +300°C. . . . . . . . . . . . . . . . . . . .
(1)
Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(2)
Input terminals are diode-clamped to the power-supply rails.
Input signals that can swing more than 0.5V beyond the supply
rails should be current-limited to 10mA or less.
(3)
Short-circuit to ground, one amplifier per package.
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handled with appropriate precautions. Failure to observe
proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.