Datasheet

"#$%
SBOS270C − AUGUST 2003 − REVISED AUGUST 2008
www.ti.com
6
ELECTRICAL CHARACTERISTICS: V
S
= +5V(continued)
Boldface limits are tested at +25°C.
At T
A
= +25°C, A
1
= 1, A
0
= 1 (Full Power: for SO-14 only), G = +4, R
F
= 453Ω, and R
L
= 100Ω, unless otherwise noted. See Figure 3 for AC
performance only.
TEST
LEVEL
(3)
OPA2674ID, OPA2674I-14D
TEST
LEVEL
(3)
MIN/MAX OVER TEMPERATURETYP
PARAMETER
TEST
LEVEL
(3)
MIN/
MAX
UNITS
−40°C to
+85°C
(2)
0°C to
+70°C
(2)
+25°C
(1)
+25°C
TEST CONDITIONS
Power Supply (Single−Supply Mode)
Specified Operating Voltage +5 V typ C
Maximum Operating Voltage 12.6 12.6 12.6 V max A
Maximum Quiescent Current V
S
= +5V, Both Channels 13.6 14.8 15.2 15.6 mA max A
Minimum Quiescent Current V
S
= +5V, Both Channels 13.6 12 11.7 11.4 mA min A
Power-Supply Rejection Ratio (PSRR) f = 100kHz, Input-Referred 52 dB typ C
Power Control (SO-14 Only)
Maximum Logic 0 A1, A0, +V
S
= +5V 1.5 1.0 0.9 0.8 V max A
Minimum Logic 1 A1, A0, +V
S
= +5V 2.4 2.7 3.1 3.3 V min A
Logic Input Current A1 = 0V, A0 = 0V, Each Line 50 80 90 95 µA max A
Supply Current at Full Power A1 = 1, A0 = 1, Both Channels 13.8 14.8 15.2 15.6 mA max A
Supply Current at Power Cutback A1 = 1, A0 = 0, Both Channels 10.2 10.8 11.1 11.4 mA max A
Supply Current at Idle Power A1 = 1, A0 = 1, Both Channels 3.0 3.2 3.5 3.8 mA max A
Supply Current at Shutdown A1 = 0, A0 = 0, Both Channels 0.6 0.9 1.0 1.1 mA max A
Output Impedance in Idle Power G = +4, f = 1MHz Ω typ C
Output Impedance in Shutdown 100 4 kΩ pF typ C
Supply Current Step Time 10% to 90% Change 200 ns typ C
Output Switching Glitch Inputs at GND ±20 mV typ C
Shutdown Isolation G = +4, 1MHz, A1 = 0, A0 = 0 85 dB typ C
Thermal Characteristics
Specification: ID, I-14D
−40 to
+85
°C
Thermal Resistance, q
JA
ID SO-8 Junction-to-Ambient 125 °C/W typ C
I-14D SO-14 100 °C/W typ C
(1)
Junction temperature = ambient for +25°C specifications.
(2)
Junction temperature = ambient at low temperature limit; junction temperature = ambient +23°C at high temperature limit for over temperature
specifications.
(3)
Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
(4)
Current considered positive out of node. V
CM
is the input common-mode voltage.
(5)
Tested < 3dB below minimum CMRR at min/max input ranges.