Datasheet

"#$%
SBOS270C − AUGUST 2003 − REVISED AUGUST 2008
www.ti.com
4
ELECTRICAL CHARACTERISTICS: V
S
= ±6V (continued)
Boldface limits are tested at +25°C.
At T
A
= +25°C, A
1
= A
0
= 1 (full power: for SO-14 only), G = +4, R
F
= 402Ω, and R
L
= 100Ω, unless otherwise noted. See Figure 1 for AC performance only.
TEST
LEVEL
(3)
OPA2674ID, OPA2674I-14D
TEST
LEVEL
(3)
MIN/MAX OVER TEMPERATURETYP
PARAMETER
TEST
LEVEL
(3)
MIN/
MAX
UNITS
−40°C to
+85°C
(2)
0°C to
+70°C
(2)
+25°C
(1)
+25°CTEST CONDITIONS
Power Supply
Specified Operating Voltage ±6 V typ C
Maximum Operating Voltage ±6.3 ±6.3 ±6.3 V max A
Maximum Quiescent Current V
S
= ±6V, Both Channels 18 18.6 18.8 19.2 mA max A
Minimum Quiescent Current V
S
= ±6V, Both Channels 18 17.4 16.5 16.0 mA min A
Power-Supply Rejection Ratio (PSRR) f = 100kHz, Input-Referred 56 51 49 48 dB min A
Power Supply (SO-14 Only)
Maximum Logic 0 A1, A0, +V
S
= +6V 2.5 2.0 1.8 1.5 V max A
Minimum Logic 1 A1, A0, +V
S
= +6V 3.3 3.6 4.0 4.2 V min A
Logic Input Current A1 = 0V, A0 = 0V, Each Line 60 90 100 105 µA max A
Supply Current at Full Power A1 = 1, A0 = 1, Both Channels 18.0 18.6 18.8 19.2 mA max A
Supply Current at Power Cutback A1 = 1, A0 = 0, Both Channels 13.3 14.2 14.4 14.8 mA max A
Supply Current at Idle Power A1 = 0, A0 = 1, Both Channels 4.0 4.8 5.1 5.3 mA max A
Supply Current at Shutdown A1 = 0, A0 = 0, Both Channels 1.0 1.3 1.4 1.5 mA max A
Output Impedance in Idle Power G = +4, f < 1MHz 0.1 Ω typ C
Output Impedance in Shutdown 100 4 kΩ pF typ C
Supply Current Step Time 10% to 90% Change 200 ns typ C
Output Switching Glitch Inputs at GND ±20 mV typ C
Shutdown Isolation G = +4, 1MHz, A1 = 0, A0 = 0 85 dB typ C
Thermal Characteristics
Specification: ID, I-14D
−40 to
+85
°C
Thermal Resistance, q
JA
ID SO-8 Junction-to-Ambient 125 °C/W typ C
I-14D SO-14 100 °C/W typ C
(1)
Junction temperature = ambient for +25°C specifications.
(2)
Junction temperature = ambient at low temperature limit; junction temperature = ambient +23°C at high temperature limit for over temperature
specifications.
(3)
Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
(4)
Current is considered positive out of node. V
CM
is the input common-mode voltage.
(5)
Tested < 3dB below minimum CMRR specification at ± CMIR limits.