Datasheet

www.ti.com
ELECTRICAL CHARACTERISTICS: V
S
= ± 5V
OPA2652
SBOS125A – JUNE 2000 – REVISED MAY 2006
At T
A
= +25 ° C, G = +2, R
F
= 402 Ω , and R
L
= 100 Ω , unless otherwise noted. See Figure 28 and Figure 29 for AC
performance only.
OPA2652U, E
MIN/MAX OVER
TYP TEMPERATURE
0 ° C to –40 ° C to MIN/ TEST
PARAMETER CONDITIONS +25 ° C +25 ° C
(2)
70 ° C
(3)
+85 ° C
(3)
UNITS MAX LEVEL
(1)
AC PERFORMANCE (Figure 28 and Figure 29 )
Small-Signal Bandwidth G = +1, R
F
= 25 Ω , V
O
= 200mV
PP
700 MHz typ C
G = +2,V
O
= 200mV
PP
200 MHz typ C
G = +5,V
O
= 200mV
PP
45 MHz typ C
Gain Bandwidth Product G ≥ +10 200 MHz typ C
Bandwidth for 0.1dB Flatness V
O
= 200mV
PP
50 MHz typ C
Peaking at a Gain of +1 G = +1, R
F
= 25 Ω , V
O
= 200mV
PP
0 dB typ C
Slew Rate 4V step 335 V/ µ s typ C
Rise-and-Fall Time 200mV step 2.0 ns typ C
4V step 10 ns typ C
Large-Signal Bandwidth V
O
= 4V
PP
50 MHz typ C
SFDR V
O
= 2V
PP
, 5MHz 66 dB typ C
Input Voltage Noise f > 1MHz 8 nV/ √ Hz typ C
Input Current Noise f > 1MHz 1.4 pA/ √ Hz typ C
Differential Gain Error NTSC, R
L
= 150 Ω 0.05 % typ C
Differential Phase Error NTSC, R
L
= 150 Ω 0.03 degrees typ C
Channel-to-Channel Crosstalk f = 5MHz –100 dBc typ C
DC PERFORMANCE
(4)
V
CM
= 0V
Open-Loop Voltage Gain (A
OL
) 63 56 55 54 dB min A
Input Offset Voltage ± 1.5 ± 7 mV max A
Average Offset Drift 5 7 µ V/ ° C max B
Input Bias Current 4 15 20 25 µ A max A
Input Bias Current Drift µ A/ ° C max B
Input Offset Current ± 0.3 ± 1.0 ± 1.4 ± 2.0 µ A max A
Input Offset Current Drift µ A/ ° C max B
INPUT
(4)
Common-Mode Input Range ± 4.0 ± 3.0 ± 2.8 ± 2.7 V min A
Common-Mode Rejection Ratio 95 75 dB min A
Input Impedance V
CM
= 0V
Differential 35 || 1 k Ω || pF typ C
Common-Mode 18 || 1 M Ω || pF typ C
(1) Test levels: (A) 100% tested at +25 ° C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value only for information.
(2) Junction temperature = ambient for +25 ° C tested specifications.
(3) Junction temperature = ambient at low temperature limit; junction temperature = ambient +23 ° C at high temperature limit for over
temperature specifications.
(4) Current is considered positive-out-of node. V
CM
is the input common-mode voltage.
3
Submit Documentation Feedback