Datasheet

"#$%
SBOS249H − JUNE 2003 − REVISED AUGUST 2008
www.ti.com
5
ELECTRICAL CHARACTERISTICS: V
S
= +5V
Boldface limits are tested at +25°C.
R
F
= 402Ω, R
L
= 100Ω, and G = +2, unless otherwise noted. See Figure 3 for AC performance only.
OPA2613ID
TYP MIN/MAX OVER TEMPERATURE
TEST
PARAMETER TEST CONDITIONS +25°C +25°C
(1)
0°C to
+70°C
(2)
−40°C to
+85°C
(2)
UNITS
MIN/
MAX
TEST
LEVEL
(3)
AC Performance (see Figure 3)
Small-Signal Bandwidth G = +1, V
O
= 0.1V
PP
, R
F
= 0Ω 230 MHz typ C
Small-Signal Bandwidth
G = +2, V
O
= 0.1V
PP
105 75 69 68 MHz min B
G = +10, V
O
= 0.1V
PP
12 10 8 8 MHz min B
Gain-Bandwidth Product G ≥ 20 118 93 78 76 MHz min B
Bandwidth for 0.1dB Gain Flatness G = +2, V
O
< 0.1V
PP
5 MHz typ C
Peaking at a Gain of +1 V
O
< 0.1V
PP
2.6 dB typ C
Large-Signal Bandwidth G = +2, V
O
= 2V
PP
21 MHz typ C
Slew Rate G = +2, 2V Step 60 47 46 46 V/µs min B
Rise-and-Fall Time G = +2, V
O
= 0.2V Step 3.8 5.0 5.6 5.7 ns typ B
Settling Time to 0.02% G = +2, V
O
= 2V Step 63 78 80 81 ns typ B
0.1% G = +2, V
O
= 2V Step 52 62 64 64 ns typ B
Harmonic Distortion G = +2, f = 1MHz, V
O
= 2V
PP
2nd-Harmonic R
L
= 20Ω to V
S
/2 −67 −60 −58 −57 dBc max B
R
L
≥ 500Ω to V
S
/2 −82 −79 −77 −76 dBc max B
3rd-Harmonic R
L
= 20Ω to V
S
/2 −84 −78 −76 −75 dBc max B
R
L
≥ 500Ω to V
S
/2 −94 −89 −87 −86 dBc max B
Input Voltage Noise f > 10kHz 1.9 2.1 2.2 2.4 nV/√Hz max B
Input Current Noise f > 10kHz 1.7 2.1 2.2 2.4 pA/√Hz max B
Channel-to-Channel Crosstalk f = 1MHz, Input-Referred −80 dBc typ C
DC Performance
(4)
Open-Loop Gain (A
OL
) V
O
= 0V, R
L
= 100Ω 95 91 89 88 dB min A
Input Offset Voltage V
CM
= 0V ±0.2 ±1.0 ±1.15 ±1.2 mV max A
Average Offset Voltage Drift V
CM
= 0V ±3.3 ±3.3 µV/°C max B
Input Bias Current V
CM
= 0V −6 −11 −12 −13.5 µA max A
Average Bias Current Drift (Magnitude) V
CM
= 0V −35 −35 nA/°C max B
Input Offset Current V
CM
= 0V ±50 ±300 ±520 ±750 nA max A
Average Offset Bias Current Drift V
CM
= 0V ±5 ±7 nA/°C max B
Input
Least Positive Input Voltage 1.2 1.4 1.4 1.5 V max A
Most Positive Input Voltage 3.8 3.6 3.6 3.5 V min A
Common-Mode Rejection Ratio (CMRR) V
CM
= ±1V 95 85 84 83 dB min A
Input Impedance A
Differential-Mode V
CM
= 0 15 1 kΩ pF typ C
Common-Mode V
CM
= 0 5 1.3 MΩ pF typ C
Output
Most Positive Output Voltage No Load 4.0 3.85 3.8 3.75 V min A
Most Positive Output Voltage
100Ω Load to 2.5V 3.95 3.8 3.75 3.7 V min A
Least Positive Output Voltage No Load 1.0 1.15 1.2 1.25 V min A
Least Positive Output Voltage
100Ω Load to 2.5V 1.05 1.20 1.25 1.3 V min A
Current Output, Sourcing V
O
= 0, Linear Operation +300 mA typ C
Current Output, Sinking V
O
= 0, Linear Operation −300 mA typ C
Short-Circuit Current Output Shorted to Mid-Supply ±400 mA typ C
Closed-Loop Output Impedance G = +2, f = 100kHz 0.01 Ω typ C
(1)
Junction temperature = ambient for +25°C tested specifications.
(2)
Junction temperature = ambient at low temperature limit; junction temperature = ambient +23°C at high temperature limit for over temperature
tested specifications.
(3)
Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
(4)
Current is considered positive-out-of-node. V
CM
is the input common-mode voltage.
(5)
Tested < 3dB below minimum CMRR specification at ± CMIR limits.