Datasheet
Table Of Contents
- features
- description
- pin designation
- functional block diagram
- Terminal Functions
- short-form description
- absolute maximum ratings
- recommended operating conditions
- electrical characteristics
- supply current into AVCC + DVCC1/2 excluding external current
- SCHMITT-trigger inputs − Ports P1, P2, P3, P4, P5, and P6; RST/NMI; JTAG: TCK, TMS, TDI/TCLK, TDO/TDI
- inputs Px.x, TAx, TBx
- leakage current − Ports P1, P2, P3, P4, P5, and P6
- outputs − Ports P1, P2, P3, P4, P5, and P6
- output frequency
- wake-up LPM3
- RAM
- LCD
- Comparator_A
- POR/brownout reset (BOR)
- SVS (supply voltage supervisor/monitor)
- DCO
- crystal oscillator, LFXT1 oscillator
- crystal oscillator, XT2 oscillator
- USART0
- 12-bit ADC, power supply and input range conditions
- 12-bit ADC, external reference
- 12-bit ADC, built-in reference
- 12-bit ADC, timing parameters
- 12-bit ADC, linearity parameters
- 12-bit ADC, temperature sensor and built-in VMID
- 12-bit DAC, supply specifications
- 12-bit DAC, linearity specifications
- 12-bit DAC, output specifications
- 12-bit DAC, reference input specifications
- 12-bit DAC, dynamic specifications; Vref = VCC, DAC12IR = 1
- operational amplifier OA, supply specifications
- operational amplifier OA, input/output specifications
- operational amplifier OA, dynamic specifications
- Flash Memory
- JTAG Interface
- JTAG Fuse
- Application Information
- input/output schematic
- Port P1, P1.0 to P1.5, input/output with Schmitt-trigger
- Port P1, P1.6, P1.7, input/output with Schmitt-trigger
- port P2, P2.0, P2.4 to P2.5, input/output with Schmitt-trigger
- port P2, P2.1 to P2.3, input/output with Schmitt-trigger
- port P2, P2.6 to P2.7, input/output with Schmitt-trigger
- port P3, P3.0 to P3.3, input/output with Schmitt-trigger
- port P3, P3.4 to P3.7, input/output with Schmitt-trigger
- port P4, P4.0 to P4.5, input/output with Schmitt-trigger
- port P4, P4.6, input/output with Schmitt-trigger
- port P4, P4.7, input/output with Schmitt-trigger
- port P5, P5.0, input/output with Schmitt-trigger
- port P5, P5.1, input/output with Schmitt-trigger
- port P5, P5.2 to P5.4, input/output with Schmitt-trigger
- port P5, P5.5 to P5.7, input/output with Schmitt-trigger
- port P6, P6.0, P6.2, and P6.4, input/output with Schmitt-trigger
- port P6, P6.1, input/output with Schmitt-trigger
- port P6, P6.3, input/output with Schmitt-trigger
- port P6, P6.5, input/output with Schmitt-trigger
- port P6, P6.6, input/output with Schmitt-trigger
- port P6, P6.7, input/output with Schmitt-trigger
- VeREF+/DAC0
- JTAG pins TMS, TCK, TDI/TCLK, TDO/TDI, input/output with Schmitt-trigger or output
- JTAG fuse check mode
- input/output schematic
- Data Sheet Revision History
- Corrections to MSP430FG43x Data Sheet (SLAS380C)
Manual Update Sheet
SLAZ565–December 2013
Corrections to MSP430FG43x Data Sheet (SLAS380C)
Document Being Updated: MSP430FG43x Mixed Signal Microcontroller
Literature Number Being Updated: SLAS380C
Page Change or Add
51 In both entries in the "Port/LCD" column of the table:
0: LCDM < 40h should be changed to 0: LCDPx < 02h.
52 In top left of the figure:
LCDM.5 should be changed to bit 0 of LCDPx, which is bit 5 of the LCDCTL register.
LCDM.6 should be changed to bit 1 of LCDPx, which is bit 6 of the LCDCTL register.
LCDM.7 should be changed to bit 2 of LCDPx, which is bit 7 of the LCDCTL register.
53 In top left of the figure:
LCDM.7 should be changed to bit 2 of LCDPx, which is bit 7 of the LCDCTL register.
54 In the table at the bottom of the page:
LCDM < 020h should be changed to LCDPx < 01h.
LCDM ≥ 020h should be changed to LCDPx ≥ 01h.
55 In top left of the figure:
1, If LCDM ≥ 020h should be changed to 1, If LCDPx ≥ 01h.
In the table at the bottom of the page:
LCDM < 020h should be changed to LCDPx < 01h.
LCDM ≥ 020h should be changed to LCDPx ≥ 01h.
56 In top left of the figure:
1, If LCDM ≥ 020h should be changed to 1, If LCDPx ≥ 01h.
In the table at the bottom of the page:
LCDM < 020h should be changed to LCDPx < 01h.
LCDM ≥ 020h should be changed to LCDPx ≥ 01h.
57 In top left of the figure:
1, If LCDM ≥ 020h should be changed to 1, If LCDPx ≥ 01h.
In the table at the bottom of the page:
LCDM < 020h should be changed to LCDPx < 01h.
LCDM ≥ 020h should be changed to LCDPx ≥ 01h.
58 In top left of the figure:
1, If LCDM ≥ 020h should be changed to 1, If LCDPx ≥ 01h.
In the LCDM column in the table at the bottom of the page:
The column header LCDM should be changed to LCDPx.
< 020h should be changed to < 01h.
≥ 020h should be changed to ≥ 01h.
59 In the Port/LCD column of the table at the top of the page:
0: LCDM < 020h should be changed to 0: LCDPx < 01h.
1
SLAZ565–December 2013 Corrections to MSP430FG43x Data Sheet (SLAS380C)
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated