Datasheet
Table Of Contents
- features
- description
- Available Options
- pin designation, DL package
- pin designation, RGZ package
- functional block diagram
- Terminal Functions
- short-form description
- absolute maximum ratings
- recommended operating conditions
- electrical characteristics
- supply current into AVCC + DVCC excluding external current
- Schmitt-trigger inputs − Ports P1, P2, P5, and P6; RST/NMI; JTAG: TCK, TMS, TDI/TCLK, TDO/TDI
- inputs Px.x, TAx
- leakage current − Ports P1, P2, P5, and P6
- outputs − Ports P1, P2, P5, and P6
- output frequency
- wake-up LPM3
- RAM
- LCD_A
- POR/brownout reset (BOR)
- DCO
- crystal oscillator, LFXT1 oscillator
- SD16_A, power supply and recommended operating conditions
- SD16_A, input range
- SD16_A, performance
- SD16_A, temperature sensor
- SD16_A, built-in voltage reference
- SD16_A, reference output buffer
- SD16_A, external reference input
- 12-bit DAC, supply specifications
- 12-bit DAC, linearity specifications
- 12-bit DAC, output specifications
- 12-bit DAC, reference input specifications
- 12-bit DAC, dynamic specifications
- operational amplifier OA, supply specifications
- operational amplifier OA, input/output specifications
- operational amplifier OA, dynamic specifications
- switches to ground
- flash memory
- JTAG interface
- JTAG fuse
- input/output schematics
- Port P1 pin schematic: P1.0, P1.1, input/output with Schmitt−trigger
- Port P1 pin schematic: P1.2, input/output with Schmitt−trigger and analog functions
- Port P1 pin schematic: P1.3, P1.5, P1.7, input/output with Schmitt−trigger and analog functions
- Port P1 pin schematic: P1.4, input/output with Schmitt−trigger and analog functions
- Port P1 pin schematic: P1.6, input/output with Schmitt−trigger and analog functions
- Port P2 pin schematic: P2.0 to P2.1, input/output with Schmitt−trigger, LCD and analog functions
- Port P2 pin schematic: P2.2 to P2.7, input/output with Schmitt−trigger, LCD and analog functions
- Port P5 pin schematic: P5.0, P5.1, P5.5 to P5.7, input/output with Schmitt−trigger and LCDfunctions
- Port P5 pin schematic: P5.2 to P5.4, input/output with Schmitt−trigger and LCD functions
- Port P6 pin schematic: P6.0, P6.2, input/output with Schmitt−trigger and analog functions
- Port P6 pin schematic: P6.1, P6.3, input/output with Schmitt−trigger and analog functions
- Port P6 pin schematic: P6.4 to P6.7, input/output with Schmitt−trigger and analog functions
- JTAG pins TMS, TCK, TDI/TCLK, TDO/TDI, input/output with Schmitt-trigger or output
- JTAG fuse check mode
- Data Sheet Revision History
MSP430FG42x0
MIXED SIGNAL MICROCONTROLLER
SLAS556A − JULY 2007 − REVISED AUGUST 2007
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
special function registers (SFRs)
The MSP430 SFRs are located in the lowest address space and are organized as byte-mode registers. SFRs
should be accessed with byte instructions.
interrupt enable registers 1 and 2
7654 0
OFIE WDTIE
321
rw–0 rw–0 rw–0
Address
0h ACCVIE NMIIE
rw–0
WDTIE: Watchdog-timer interrupt enable. Inactive if watchdog mode is selected.
Active if watchdog timer is configured as a general-purpose timer.
OFIE: Oscillator-fault-interrupt enable
NMIIE: Nonmaskable-interrupt enable
ACCVIE: Flash access violation interrupt enable
7654 0321
Address
01h
rw–0
BTIE
BTIE: Basic timer interrupt enable
interrupt flag registers 1 and 2
7654 0
OFIFG WDTIFG
321
rw–0 rw–1 rw–(0)
Address
02h NMIIFG
WDTIFG: Set on watchdog timer overflow (in watchdog mode) or security key violation
Reset on V
CC
power-on or a reset condition at the RST/NMI pin in reset mode
OFIFG: Flag set on oscillator fault
NMIIFG: Set via RST
/NMI pin
7654 0321
Address
03h
BTIFG
rw–0
BTIFG: Basic timer flag