Datasheet

MSP430FE42x2
MIXED SIGNAL MICROCONTROLLER
SLAS616 − JULY 2008
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings
†
Voltage applied at V
CC
to V
SS
−0.3 V to + 4.1 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage applied to any pin (see Note 1) −0.3 V to V
CC
+ 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diode current at any device terminal ±2 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature (unprogrammed device) −55°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature (programmed device) −40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltages referenced to V
SS
. The JTAG fuse-blow voltage, V
FB
, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TDI/TCLK pin when blowing the JTAG fuse.
recommended operating conditions (see Note 1)
PARAMETER MIN NOM MAX UNITS
Supply voltage during program execution; ESP430 and SD16 disabled,
V
CC
(AV
CC
= DV
CC
= V
CC
) (see Note 1)
1.8 3.6 V
Supply voltage during program execution; SVS enabled, PORON = 1, ESP430 and SD16 disabled,
V
CC
(AV
CC
= DV
CC
= V
CC
) (see Note 1 and Note 2)
2.0 3.6 V
Supply voltage during program execution; ESP430 or SD16 enabled or during programming of
flash memory, V
CC
(AV
CC
= DV
CC
= V
CC
) (see Note 1)
2.7 3.6 V
Supply voltage (see Note 1), V
SS
(AV
SS
= DV
SS
= V
SS
) 0 0 V
Operating free-air temperature range, T
A
−40 85 °C
LF selected, XTS_FLL=0 Watch crystal 32768 Hz
LFXT1 crystal frequency, f
(
LFXT1
)
(see Note 3)
XT1 selected, XTS_FLL=1 Ceramic resonator 450 8000 kHz
LFXT1
crystal
frequency,
f
(LFXT1)
(see
Note
3)
XT1 selected, XTS_FLL=1 Crystal 1000 8000 kHz
Processor frequency (signal MCLK) f (see Note 4)
V
CC
= 2.7 V dc 8.4
MHz
Processor frequency (signal MCLK), f
(System)
(see Note 4)
V
CC
= 3.6 V dc 8.4
MHz
NOTES: 1. It is recommended to power AV
CC
and DV
CC
from the same source. A maximum difference of 0.3 V between AV
CC
and DV
CC
can
be tolerated during power up and operation.
2. The minimum operating supply voltage is defined according to the trip point where POR is going active by decreasing supply voltage.
POR is going inactive when the supply voltage is raised above minimum supply voltage plus the hysteresis of the SVS circuitry.
3. The LFXT1 oscillator in LF-mode requires a watch crystal.
4. For frequencies above 8 MHz, MCLK is sourced by the built-in oscillator (DCO and FLL+).