Datasheet

MSP430F5510, MSP430F5509, MSP430F5508, MSP430F5507
MSP430F5506, MSP430F5505, MSP430F5504, MSP430F5503
MSP430F5502, MSP430F5501, MSP430F5500
www.ti.com SLAS645I –JULY 2009–REVISED NOVEMBER 2013
USCI (UART Mode) Recommended Operating Conditions
PARAMETER CONDITIONS V
CC
MIN TYP MAX UNIT
Internal: SMCLK, ACLK
f
USCI
USCI input clock frequency External: UCLK f
SYSTEM
MHz
Duty cycle = 50% ± 10%
BITCLK clock frequency
f
BITCLK
1 MHz
(equals baud rate in MBaud)
USCI (UART Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS V
CC
MIN TYP MAX UNIT
2.2 V 50 600
t
τ
UART receive deglitch time
(1)
ns
3 V 50 600
(1) Pulses on the UART receive input (UCxRX) shorter than the UART receive deglitch time are suppressed. To ensure that pulses are
correctly recognized, their duration should exceed the maximum specification of the deglitch time.
USCI (SPI Master Mode) Recommended Operating Conditions
PARAMETER CONDITIONS V
CC
MIN TYP MAX UNIT
Internal: SMCLK, ACLK
f
USCI
USCI input clock frequency f
SYSTEM
MHz
Duty cycle = 50% ± 10%
USCI (SPI Master Mode)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
(see Note
(1)
, Figure 12 and Figure 13)
PARAMETER TEST CONDITIONS V
CC
MIN TYP MAX UNIT
SMCLK, ACLK
f
USCI
USCI input clock frequency f
SYSTEM
MHz
Duty cycle = 50% ± 10%
1.8 V 55
PMMCOREV = 0 ns
3 V 38
t
SU,MI
SOMI input data setup time
2.4 V 30
PMMCOREV = 3 ns
3 V 25
1.8 V 0
PMMCOREV = 0 ns
3 V 0
t
HD,MI
SOMI input data hold time
2.4 V 0
PMMCOREV = 3 ns
3 V 0
1.8 V 20
UCLK edge to SIMO valid,
ns
C
L
= 20 pF, PMMCOREV = 0
3 V 18
t
VALID,MO
SIMO output data valid time
(2)
2.4 V 16
UCLK edge to SIMO valid,
ns
C
L
= 20 pF, PMMCOREV = 3
3 V 15
1.8 V -10
C
L
= 20 pF, PMMCOREV = 0 ns
3 V -8
t
HD,MO
SIMO output data hold time
(3)
2.4 V -10
C
L
= 20 pF, PMMCOREV = 3 ns
3 V -8
(1) f
UCxCLK
= 1/2t
LO/HI
with t
LO/HI
≥ max(t
VALID,MO(USCI)
+ t
SU,SI(Slave)
, t
SU,MI(USCI)
+ t
VALID,SO(Slave)
).
For the slave's parameters t
SU,SI(Slave)
and t
VALID,SO(Slave)
see the SPI parameters of the attached slave.
(2) Specifies the time to drive the next valid data to the SIMO output after the output changing UCLK clock edge. See the timing diagrams
in Figure 12 and Figure 13.
(3) Specifies how long data on the SIMO output is valid after the output changing UCLK clock edge. Negative values indicate that the data
on the SIMO output can become invalid before the output changing clock edge observed on UCLK. See the timing diagrams in
Figure 12 and Figure 13.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 63
Product Folder Links: MSP430F5510 MSP430F5509 MSP430F5508 MSP430F5507 MSP430F5506 MSP430F5505
MSP430F5504 MSP430F5503 MSP430F5502 MSP430F5501 MSP430F5500