Datasheet
Table Of Contents
- features
- description
- DEVELOPMENT TOOL SUPPORT
- pin designation, MSP430x4351IPN, MSP430x4361IPN, MSP430x4371IPN
- pin designation, MSP430x435IPZ, MSP430x436IPZ, MSP430x4371IPZ
- pin designation, MSP430x435IPN, MSP430x436IPN, MSP430x437IPN
- pin designation, MSP430x435IPZ, MSP430x436IPZ, MSP430x437IPZ
- pin designation, MSP430x4481IPZ, MSP430x4491IPZ
- pin designation, MSP430x447IPZ, MSP430x448IPZ, MSP430x449IPZ
- MSP430x43x1 functional block diagram
- MSP430x43x functional block diagram
- MSP430x44x1 functional block diagram
- MSP430x44x functional block diagram
- MSP430x43x1 Terminal Functions
- MSP430x43x Terminal Functions
- MSP430x44x1 Terminal Functions
- MSP430x44x Terminal Functions
- short-form description
- CPU
- instruction set
- operating modes
- interrupt vector addresses
- special function registers
- interrupt enable 1 and 2
- interrupt flag register 1 and 2
- module enable registers 1 and 2
- memory organization
- bootstrap loader (BSL)
- flash memory
- peripherals
- digital I/O
- oscillator and system clock
- brownout, supply voltage supervisor (SVS)
- hardware multiplier (MSP430x44x(1) only)
- watchdog timer (WDT)
- USART0
- USART1 (MSP430x44x(1) only)
- Timer_A3
- Timer_B3 (MSP430x43x(1) only)
- Timer_B7 (MSP430x44x(1) only)
- Comparator_A
- ADC12 (not implemented in MSP430x43x1 and MSP430x44x1)
- Basic Timer1
- LCD driver
- peripheral file map
- absolute maximum ratings
- recommended operating conditions
- electrical characteristics
- supply current into AVCC + DVCC excluding external current
- Schmitt-trigger inputs - ports P1, P2, P3, P4, P5, P6
- standard inputs - RST/NMI, JTAG (TCK, TMS, TDI/TCLK)
- inputs Px.x, TAx, TBx
- leakage current
- outputs - ports P1, P2, P3, P4, P5, P6
- output frequency
- wake-up LPM3
- RAM
- LCD
- Comparator_A
- POR/brownout reset (BOR)
- supply voltage supervisor/monitor (SVS)
- DCO
- crystal oscillator, LFXT1 oscillator
- crystal oscillator, XT2 oscillator
- USART0, USART1
- 12-bit ADC, power supply and input range conditions
- 12-bit ADC, external reference
- 12-bit ADC, built-in reference
- 12-bit ADC, timing parameters
- 12-bit ADC, linearity parameters
- 12-bit ADC, temperature sensor and built-in VMID
- flash memory
- JTAG interface
- JTAG fuse
- APPLICATION INFORMATION
- input/output schematics
- port P1, P1.0 to P1.5, input/output with Schmitt trigger
- port P1, P1.6, P1.7, input/output with Schmitt trigger
- port P2, P2.0, P2.4 to P2.5, input/output with Schmitt trigger
- port P2, P2.1 to P2.3, input/output with Schmitt trigger
- port P2, P2.6 to P2.7, input/output with Schmitt trigger
- port P3, P3.0 to P3.3, input/output with Schmitt trigger
- port P3, P3.4 to P3.7, input/output with Schmitt trigger
- port P4, P4.0 to P4.7, input/output with Schmitt trigger
- port P5, P5.0 to P5.1, input/output with Schmitt trigger
- port P5, P5.2 to P5.4, input/output with Schmitt trigger
- port P5, P5.5 to P5.7, input/output with Schmitt trigger
- port P6, P6.0 to P6.6, input/output with Schmitt trigger
- port P6, P6.0 to P6.6, input/output with Schmitt trigger
- port P6, P6.7, input/output with Schmitt trigger
- JTAG pins TMS, TCK, TDI/TCLK, TDO/TDI, input/output with Schmitt trigger or output
- JTAG fuse check mode
- input/output schematics
- Data Sheet Revision History
MSP430x43x1, MSP430x43x, MSP430x44x1, MSP430x44x
MIXED SIGNAL MICROCONTROLLER
SLAS344G − JANUARY 2002 − REVISED OCTOBER 2009
27
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
module enable registers 1 and 2
7654 0
UTXE0
32 1
rw–0 rw–0
Address
04h
URXE0
USPIE0
URXE0: USART0: UART mode receive enable
UTXE0: USART0: UART mode transmit enable
USPIE0: USART0: SPI mode transmit and receive enable
7654 0
UTXE1
32 1
rw–0 rw–0
Address
05h
URXE1
USPIE1
URXE1: USART1: UART mode receive enable (MSP430F44x(1) devices only)
UTXE1: USART1: UART mode transmit enable (MSP430F44x(1) devices only)
USPIE1: USART1: SPI mode transmit and receive enable (MSP430F44x(1) devices only)
rw–0,1:
Legend: rw:
Bit Can Be Read and Written
Bit Can Be Read and Written. It Is Reset or Set by PUC.
Bit Can Be Read and Written. It Is Reset or Set by POR.
SFR Bit Not Present in Device
rw–(0,1):
memory organization
MSP430F435
MSP430F4351
MSP430F436
MSP430F4361
MSP430F437
MSP430F4371
MSP430F447
MSP430F448
MSP430F4481
MSP430F449
MSP430F4491
Memory
Main: interrupt vector
Main: code memory
Size
Flash
Flash
16KB
0FFFFh − 0FFE0h
0FFFFh − 0C000h
24KB
0FFFFh − 0FFE0h
0FFFFh − 0A000h
32KB
0FFFFh − 0FFE0h
0FFFFh − 08000h
48KB
0FFFFh − 0FFE0h
0FFFFh − 04000h
60KB
0FFFFh − 0FFE0h
0FFFFh − 01100h
Information memory Size
Flash
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
256 Byte
010FFh − 01000h
Boot memory Size
ROM
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
1KB
0FFFh − 0C00h
RAM Size 512 Byte
03FFh − 0200h
1KB
05FFh − 0200h
1KB
05FFh − 0200h
2KB
09FFh − 0200h
2KB
09FFh − 0200h
Peripherals 16-bit
8-bit
8-bit SFR
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
01FFh − 0100h
0FFh − 010h
0Fh − 00h
bootstrap loader (BSL)
The MSP430 bootstrap loader (BSL) enables users to program the flash memory or RAM using a UART serial
interface. Access to the MSP430 memory via the BSL is protected by user-defined password. For complete
description of the features of the BSL and its implementation, see the MSP430 Memory Programming User’s
Guide, literature number SLAU265.
BSL Function PN Package Pins PZ Package Pins
Data Transmit 67 - P1.0 87 - P1.0
Data Receive 66 - P1.1 86 - P1.1