Datasheet
MSP430F5229, MSP430F5227, MSP430F5224, MSP430F5222
MSP430F5219, MSP430F5217, MSP430F5214, MSP430F5212
SLAS718D –NOVEMBER 2012–REVISED OCTOBER 2013
www.ti.com
Crystal Oscillator, XT1, Low-Frequency Mode
(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER TEST CONDITIONS V
CC
MIN TYP MAX UNIT
f
OSC
= 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 1, 0.075
T
A
= 25°C
Differential XT1 oscillator crystal f
OSC
= 32768 Hz, XTS = 0,
ΔI
DVCC.LF
current consumption from lowest XT1BYPASS = 0, XT1DRIVEx = 2, 3.0 V 0.170 µA
drive setting, LF mode T
A
= 25°C
f
OSC
= 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 3, 0.290
T
A
= 25°C
XT1 oscillator crystal frequency,
f
XT1,LF0
XTS = 0, XT1BYPASS = 0 32768 Hz
LF mode
XT1 oscillator logic-level square- XTS = 0, XT1BYPASS = 1
(2)(3)
f
XT1,LF,SW
10 32.768 50 kHz
wave input frequency, LF mode XT1BYPASSLV = 0 or 1
XTS = 0, XT1BYPASS = 0,
XT1DRIVEx = 0, 210
f
XT1,LF
= 32768 Hz, C
L,eff
= 6 pF
Oscillation allowance for
OA
LF
kΩ
LF crystals
(4)
XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 1, 300
f
XT1,LF
= 32768 Hz, C
L,eff
= 12 pF
XTS = 0, XCAPx = 0
(6)
2
XTS = 0, XCAPx = 1 5.5
Integrated effective load
C
L,eff
pF
capacitance, LF mode
(5)
XTS = 0, XCAPx = 2 8.5
XTS = 0, XCAPx = 3 12.0
XTS = 0, Measured at ACLK,
Duty cycle, LF mode 30 70 %
f
XT1,LF
= 32768 Hz
Oscillator fault frequency, XTS = 0, XT1BYPASS = 1
(8)
,
f
Fault,LF
10 10000 Hz
LF mode
(7)
XT1BYPASSLV = 0 or 1
f
OSC
= 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 0, 1000
T
A
= 25°C, C
L,eff
= 6 pF
t
START,LF
Startup time, LF mode 3.0 V ms
f
OSC
= 32768 Hz, XTS = 0,
XT1BYPASS = 0, XT1DRIVEx = 3, 500
T
A
= 25°C, C
L,eff
= 12 pF
(1) To improve EMI on the XT1 oscillator, the following guidelines should be observed.
(a) Keep the trace between the device and the crystal as short as possible.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and techniques that avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, make sure that it does not induce capacitive or resistive leakage between the oscillator pins.
(2) When XT1BYPASS is set, XT1 circuits are automatically powered down. Input signal is a digital square wave with parametrics defined in
the Schmitt-Trigger Inputs section of this data sheet. When in crystal bypass mode, XIN can be configured so that it can support an
input digital waveform with swing levels from DVSS to DVCC (XT1BYPASSLV = 0) or DVSS to DVIO (XT1BYPASSLV = 1). In this case,
it is required that the pin be configured properly for the intended input swing.
(3) Maximum frequency of operation of the entire device cannot be exceeded.
(4) Oscillation allowance is based on a safety factor of 5 for recommended crystals. The oscillation allowance is a function of the
XT1DRIVEx settings and the effective load. In general, comparable oscillator allowance can be achieved based on the following
guidelines, but each application should be evaluated based on the actual crystal selected:
(a) For XT1DRIVEx = 0, C
L,eff
≤ 6 pF
(b) For XT1DRIVEx = 1, 6 pF ≤ C
L,eff
≤ 9 pF
(c) For XT1DRIVEx = 2, 6 pF ≤ C
L,eff
≤ 10 pF
(d) For XT1DRIVEx = 3, C
L,eff
≥ 6 pF
(5) Includes parasitic bond and package capacitance (approximately 2 pF per pin).
Because the PCB adds additional capacitance, it is recommended to verify the correct load by measuring the ACLK frequency. For a
correct setup, the effective load capacitance should always match the specification of the used crystal.
(6) Requires external capacitors at both terminals. Values are specified by crystal manufacturers.
(7) Frequencies below the MIN specification set the fault flag. Frequencies above the MAX specification do not set the fault flag.
Frequencies between the MIN and MAX specifications might set the flag.
(8) Measured with logic-level input frequency but also applies to operation with crystals.
60 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: MSP430F5229 MSP430F5227 MSP430F5224 MSP430F5222 MSP430F5219 MSP430F5217
MSP430F5214 MSP430F5212