Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsDev KitsPCB design board

121

122

123

124

125

126

127

128

129

130

MSP-TS430PEU128

www.ti.com

Table B-32. MSP-TS430PEU128 Bill of Materials

No. Per

Pos. Ref Des Description DigiKey Part No. Comment

Board

94x119.4mm, 4 layers MSP-TS430PEU128 4 layers, green solder mask

1 PCB 1

Rev. 1.1

2 D1 1 green LED, DIODE0805 516-1434-1-ND

3 JP1, JP2, JP4 3 2-pin header, male, TH SAM1035-02-ND Place jumper on header

JP5, JP6, JP7, JP8, 3-pin header, male, TH SAM1035-03-ND Place jumpers on pins 1-2 (SBW)

4 6

JP9, JP10

5 JP11, JP12, JP13 3 4-pin header, male, TH SAM1035-04-ND Place jumpers on pins 1-2 (AVCC=VCC)

6 JP3 1 4-pin header, male, TH SAM1035-04-ND Place jumpers on pins 1-2

JP1, JP2, JP3, JP4, Jumper WM4592-ND

JP5, JP6, JP7, JP8,

7 13

JP9, JP10, JP11,

JP12, JP13

8 R1, R2, R4, R6, R8 5 0R, 0805 541-0.0ATR-ND

9 R10, R11 2 0R, 0805 541-0.0ATR-ND DNP

10 C3 1 2.2nF, CSMD0805 490-1628-2-ND DNP

C13, C14, C16, 4.7uF, 6.3V, CSMD0805 587-1302-2-ND

11 7

C17, C18, C19, C29

12 C11 1 10uF, 6.3V, CSMD0805 445-1372-2-ND

13 C12 1 10uF, 6.3V, CSMD0805 445-1372-2-ND DNP

14 C1, C2 2 12pF, CSMD0805 490-5531-2-ND DNP

15 R5 1 47K, 0805 311-47KARTR-ND

C4, C5, C6, C7, C8, 100nF, CSMD0805 311-1245-2-ND

16 6

C15

17 C9 1 100nF, CSMD0805 311-1245-2-ND DNP

18 R3, R7 2 330R, 0805 541-330ATR-ND

19 C10, C26 2 470nF, CSMD0805 587-1282-2-ND

20 BOOTST 1 10-pin connector, male, TH HRP10H-ND DNP, keep vias free of solder

21 JTAG 1 14-pin connector, male, TH HRP14H-ND

22 IC1 Socket 1 Socket: IC500-1284-009P Manuf. Yamaichi

23 IC1 2 MSP430F67791IPEU DNP: enclosed with kit. Is supplied by TI

24 J5 1 3-pin header, male, TH SAM1035-03-ND

Crystal: MS3V-T1R 32.768kHz DNP: Crystal enclosed with kit. Keep vias

25 Q1 1

12.5pF ±20ppm free of solder

26 TP1, TP2 2 Test point DNP, keep vias free of solder

26-pin header, TH SAM1029-26-ND DNP: Headers enclosed with kit. Keep vias

27 J2,J4 2

free of solder.

26-pin receptable, TH SAM1213-26-ND DNP: Receptacles enclosed with kit. Keep

28 J2,J4 2

vias free of solder.

38-pin header, TH SAM1029-38-ND DNP: Headers enclosed with kit. Keep vias

29 J1, J3 2

free of solder.

38-pin receptable, TH SAM1213-38-ND DNP: Receptacles enclosed with kit. Keep

30 J1, J3 2

vias free of solder.

31 Rubber feet 4 Rubber feet Buerklin: 20H1724 apply to bottom side corners

124

Hardware SLAU278Q–May 2009–Revised February 2014

Submit Documentation Feedback