Datasheet
ECCN 5E002 TSPA - Technology / Software Publicly Available
CC430F6137, CC430F6135, CC430F6127, CC430F6126, CC430F6125
CC430F5137, CC430F5135, CC430F5133
SLAS554H –MAY 2009–REVISED SEPTEMBER 2013
www.ti.com
RF Receive, Overall
T
A
= 25°C, V
CC
= 3 V (unless otherwise noted)
(1)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Digital channel filter bandwidth
(2)
58 812 kHz
25 MHz to 1 GHz -68 -57
Spurious emissions
(3) (4)
dBm
Above 1 GHz -66 -47
RX latency Serial operation
(5)
9 bit
(1) All measurement results are obtained using the EM430F6137RF900 with BOM according to tested frequency range (see Table 48).
(2) User programmable. The bandwidth limits are proportional to crystal frequency (given values assume a 26.0 MHz crystal)
(3) Typical radiated spurious emission is -49 dBm measured at the VCO frequency
(4) Maximum figure is the ETSI EN 300 220 limit
(5) Time from start of reception until data is available on the receiver data output pin is equal to 9 bit.
RF Receive, 315 MHz
T
A
= 25°C, V
CC
= 3 V (unless otherwise noted)
(1)
2-FSK, 1% packet error rate, 20-byte packet length, Sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF = 0 (unless
otherwise noted)
DATA RATE
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
(kBaud)
0.6 14.3kHz deviation, 58kHz digital channel filter bandwidth -117
1.2 5.2kHz deviation, 58kHz digital channel filter bandwidth
(2)
-111
Receiver sensitivity 38.4 20kHz deviation, 100kHz digital channel filter bandwidth
(3)
-103 dBm
250 127kHz deviation, 540kHz digital channel filter bandwidth
(4)
-95
500 MSK, 812kHz digital channel filter bandwidth
(4)
-86
(1) All measurement results are obtained using the EM430F6137RF900 with BOM according to tested frequency range (see Table 48).
(2) Sensitivity can be traded for current consumption by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical current consumption is then
reduced by about 2mA close to the sensitivity limit. The sensitivity is typically reduced to -109dBm.
(3) Sensitivity can be traded for current consumption by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical current consumption is then
reduced by about 2mA close to the sensitivity limit. The sensitivity is typically reduced to -102dBm.
(4) MDMCFG2.DEM_DCFILT_OFF=1 can not be used for data rates ≥ 250kBaud.
RF Receive, 433 MHz
T
A
= 25°C, V
CC
= 3 V (unless otherwise noted)
(1)
2-FSK, 1% packet error rate, 20-byte packet length, Sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF = 0 (unless
otherwise noted)
DATA RATE
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
(kBaud)
0.6 14.3kHz deviation, 58kHz digital channel filter bandwidth -114
1.2 5.2-kHz deviation, 58-kHz digital channel filter bandwidth
(2)
-111
38.4 20-kHz deviation, 100-kHz digital channel filter bandwidth
(3)
-104
Receiver sensitivity dBm
127-kHz deviation, 540-kHz digital channel filter bandwidth
250 -93
(4)
500 MSK, 812kHz digital channel filter bandwidth
(4)
-85
(1) All measurement results are obtained using the EM430F6137RF900 with BOM according to tested frequency range (see Table 48).
(2) Sensitivity can be traded for current consumption by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical current consumption is then
reduced by about 2mA close to the sensitivity limit. The sensitivity is typically reduced to -109dBm.
(3) Sensitivity can be traded for current consumption by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical current consumption is then
reduced by about 2mA close to the sensitivity limit. The sensitivity is typically reduced to -101dBm.
(4) MDMCFG2.DEM_DCFILT_OFF=1 can not be used for data rates ≥ 250kBaud.
76 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: CC430F6137 CC430F6135 CC430F6127 CC430F6126 CC430F6125 CC430F5137
CC430F5135 CC430F5133