Datasheet

 
 
SBAS323G − JUNE 2004 − REVISED OCTOBER 2007
www.ti.com
8
DIGITAL CHARACTERISTICS: DV
DD
= 2.7V to 5.25V
All specifications from T
MIN
to T
MAX
, FMCON = 10h, all digital outputs high, PDCON = 00h (all peripherals ON) or PDCON = FFh (all peripherals OFF), PSEN and
ALE enabled (all peripherals ON) or PSEN
and ALE disabled (all peripherals OFF), unless otherwise specified.
MSC1211/12/13/14
PARAMETER CONDITIONS
MIN TYP MAX
UNITS
Digital Power-Supply Requirements
DV
DD
2.7 3 3.6 V
Normal Mode, f
OSC
= 1MHz, peripherals OFF 0.9 mA
Normal Mode, f
OSC
= 1MHz, peripherals ON 1.1 mA
Digital Power-Supply Current
Normal Mode, f
OSC
= 8MHz, peripherals OFF 5.7 mA
Digital Power-Supply Current
Normal Mode, f
OSC
= 8MHz, peripherals ON 7.5 mA
Crystal Operation Stop Mode
(1)
100 nA
DV
DD
4.75 5 5.25 V
Normal Mode, f
OSC
= 1MHz, peripherals OFF 1.7 mA
Normal Mode, f
OSC
= 1MHz, peripherals ON 2.4 mA
Digital Power-Supply Current
Normal Mode, f
OSC
= 8MHz, peripherals OFF 11 mA
Digital Power-Supply Current
Normal Mode, f
OSC
= 8MHz, peripherals ON 14.8 mA
Crystal Operation Stop Mode
(1)
100 nA
DIGITAL INPUT/OUTPUT (CMOS)
Logic Level
V
IH
(except XIN pin) 0.6 • DV
DD
DV
DD
V
Logic Level
V
IL
(except XIN pin) DGND 0.2 • DV
DD
V
I/O Pin Hysteresis 700 mV
Ports 0−3, Input Leakage Current, Input Mode V
IH
= DV
DD
or V
IH
= 0V < 1 pA
Pins EA, RST Input Leakage Current < 1 pA
V
OL
, ALE, PSEN, Ports 0−3, All Output Modes
I
OL
= −1mA DGND 0.4 V
V
OL
, ALE, PSEN, Ports 0−3, All Output Modes
I
OL
= −30mA (5V), −20mA (3V) 1.5 V
V
OH
, ALE, PSEN, Ports 0−3, Strong Drive Output
I
OH
= 1mA DV
DD
− 0.4 DV
DD
− 0.1 DV
DD
V
V
OH
, ALE, PSEN, Ports 0−3, Strong Drive Output
I
OH
= 30mA (5V), 20mA (5V) DV
DD
− 1.5 V
Ports 0−3, Pull-Up Resistors 9 kΩ
Pins ALE, PSEN, Pull-Up Resistors During Reset Flash Programming Mode Only 9 kΩ
OSCILLATOR/CLOCK INPUT/OUTPUT
External Oscillator/Clock
V
IH
(except XIN pin) XOUT must be unconnected 0.6 • DV
DD
DV
DD
V
External Oscillator/Clock
V
IL
(except XIN pin) XOUT must be unconnected DGND 0.2 • DV
DD
V
(1)
Digital Brownout Detect disabled (HCR1.2 = 1), Low Voltage Detect disabled (LVDCON.3 = 1). Ports configured for CMOS output low.
FLASH MEMORY CHARACTERISTICS: DV
DD
= 2.7V to 5.25V
MSC1211/12/13/14
PARAMETER CONDITIONS
MIN TYP MAX
UNITS
Flash Memory Endurance 100,000 1,000,000 Cycles
Flash Memory Data Retention 100 Years
Mass and Page Erase Time Set with FER in FTCON 10 ms
Flash Memory Write Time Set with FWR in FTCON 30 40 µs
Flash Programming Current
(1)
DV
DD
= 3.0V 10 mA
Flash Programming Current
(1)
DV
DD
= 5.0V 25 mA
(1)
Peak current during Mass and Page Erase Time and Memory Write Time.