Datasheet

MPC506A, MPC507A
2
SBFS018A
www.ti.com
ELECTRICAL CHARACTERISTICS
Supplies = +15V, –15V; V
REF
(Pin 13) = Open; V
AH
(Logic Level High) = +4.0V; V
AL
(Logic Level Low) = +0.8V unless otherwise specified.
MPC506A/MPC507A
PARAMETER TEMP MIN TYP MAX UNITS
ANALOG CHANNEL CHARACTERISTICS
V
S
, Analog Signal Range Full –15 +15 V
R
ON
, On Resistance
(1)
+25°C 1.3 1.5 kΩ
Full 1.5 1.8 kΩ
I
S
(OFF), Off Input Leakage Current +25°C 0.5 nA
Full 10 nA
I
D
(OFF), Off Output Leakage Current +25°C 0.2 nA
MPC506A Full 5 nA
MPC507A Full 5 nA
I
D
(OFF) with Input Overvoltage Applied
(2)
+25°C2µA
I
D
(ON), On Channel Leakage Current +25°C2nA
MPC506A Full 10 nA
MPC507A Full 10 nA
I
DIFF
Differential Off Output Leakage Current
(MPC507A Only) Full 10 nA
DIGITAL INPUT CHARACTERISTICS
V
AL
, Input Low Threshold Full 0.8 V
V
AH
, Input High Threshold
(3)
Full 4.0 V
V
AL
, MOS Drive
(4)
+25°C 0.8 V
V
AH
, MOS Drive
(4)
+25°C 6.0 V
I
A
, Input Leakage Current (High or Low)
(5)
Full 1.0 µA
SWITCHING CHARACTERISTICS
t
A
, Access Time +25°C 0.3 µs
Full 0.6 µs
t
OPEN
, Break-Before-Make Delay +25°C2580 ns
t
ON
(EN), Enable Delay (ON) +25°C 200 ns
Full 500 ns
t
OFF
(EN), Enable Delay (OFF) +25°C 250 ns
Full 500 ns
Settling Time (0.1%) +25°C 1.2 µs
(0.01%) +25°C 3.5 µs
"OFF Isolation"
(6)
+25°C5068 dB
C
S
(OFF), Channel Input Capacitance +25°C5pF
C
D
(OFF), Channel Output Capacitance: MPC506A +25°C50pF
MPC507A +25°C25pF
C
A
, Digital Input Capacitance 25°C5pF
C
DS
, (OFF), Input to Output Capacitance +25°C 0.1 pF
POWER REQUIREMENTS
P
D
, Power Dissipation Full 7.5 mW
I+, Current Pin 1
(7)
Full 0.7 1.5 mA
I–, Current Pin 27
(7)
Full 5 20 µA
NOTES: (1) V
OUT
= ±10V, I
OUT
= –100µA. (2) Analog overvoltage = ±33V. (3) To drive from DTL/TTL circuits. 1kΩ pull-up resistors to +5.0V supply are recommended.
(4) V
REF
= +10V. (5) Digital input leakage is primarily due to the clamp diodes. Typical leakage is less than 1nA at 25°C. (6) V
EN
= 0.8V, R
L
= 1kΩ,
C
L
= 15pF, V
S
= 7Vrms, f = 100kHz. Worst-case isolation occurs on channel 8 due to proximity of the output pins. (7) V
EN
, V
A
= 0V or 4.0V.