Datasheet

LMV981-N, LMV982-N
SNOS976L NOVEMBER 2001REVISED MARCH 2013
www.ti.com
1.8V AC Electrical Characteristics
Unless otherwise specified, all limits ensured for T
J
= 25°C. V
+
= 1.8V, V
= 0V, V
CM
= V
+
/2, V
O
= V
+
/2, R
L
> 1 M and SHDN
tied to V
+
. Boldface limits apply at the temperature extremes. See
(1)
.
Parameter Test Conditions Min
(2)
Typ
(3)
Max
(2)
Units
SR Slew Rate See
(4)
0.35 V/μs
GBW Gain-Bandwidth Product 1.4 MHz
Φ
m
Phase Margin 67 deg
G
m
Gain Margin 7 dB
e
n
Input-Referred Voltage Noise f = 10 kHz, V
CM
= 0.5V 60 nV/Hz
i
n
Input-Referred Current Noise f = 10 kHz 0.08 pA/Hz
THD Total Harmonic Distortion f = 1kHz, A
V
= +1 0.023
%
R
L
= 600, V
IN
= 1 V
PP
Amp-to-Amp Isolation See
(5)
123 dB
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self heating where T
J
> T
A
. See Application Note section for information on temperature derating of
this device. Absolute Maximum Ratings indicated junction temperature limits beyond which the device may be permanently degraded,
either mechanically or electrically.
(2) All limits are specified by testing or statistical analysis.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) Connected as voltage follower with input step from V
to V
+
. Number specified is the slower of the positive and negative slew rates.
(5) Input referred, R
L
= 100k connected to V
+
/2. Each amp excited in turn with 1kHz to produce V
O
= 3V
PP
. (For Supply Voltages <3V, V
O
= V
+
).
2.7V DC Electrical Characteristics
Unless otherwise specified, all limits ensured for T
J
= 25°C. V
+
= 2.7V, V
= 0V, V
CM
= V
+
/2, V
O
= V
+
/2, R
L
> 1 M and SHDN
tied to V
+
. Boldface limits apply at the temperature extremes. See
(1)
.
Parameter Test Conditions Min
(2)
Typ
(3)
Max
(2)
Units
V
OS
Input Offset Voltage LMV981-N (Single) 1 4
mV
6
LMV982 (Dual) 1 6
mV
7.5
TCV
OS
Input Offset Voltage Average Drift 5.5 μV/°C
I
B
Input Bias Current 15 35
nA
50
I
OS
Input Offset Current 8 25
nA
40
I
S
Supply Current (per channel) 105 190
210
In Shutdown LMV981-N (Single) 0.061 1
μA
2
LMV982 (Dual) 0.101 3.5
5
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self heating where T
J
> T
A
. See Application Note section for information on temperature derating of
this device. Absolute Maximum Ratings indicated junction temperature limits beyond which the device may be permanently degraded,
either mechanically or electrically.
(2) All limits are specified by testing or statistical analysis.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
4 Submit Documentation Feedback Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LMV981-N LMV982-N