Datasheet

1
2
3
+IN
GND
-IN
6
5
4
V
+
OUT
SHDN
TOP MARK
LMV341-N, LMV342-N, LMV344-N
www.ti.com SNOS990G –APRIL 2002–REVISED MARCH 2013
5V DC Electrical Characteristics
(1)
(continued)
Unless otherwise specified, all limits specified for T
J
= 25°C, V
+
= 5V, V
−
= 0V, V
CM
= V
+
/2, V
O
= V
+
/2 and R
L
> 1MΩ.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min Typ Max Units
(2) (3) (2)
V
O
Output Swing R
L
= 2kΩ to 2.5V 32 60
95
mV
60 34
95
R
L
= 10kΩ to 2.5V 7 30
40
mV
30 7
40
I
O
Output Short Circuit Current Sourcing 85 113
mA
Sinking 50 75
t
on
Turn-on Time from Shutdown (LMV341-N) 5 µs
V
SD
Shutdown Pin Voltage Range ON Mode (LMV341-N) 3.1 to 5 4.5 to 5.0
V
Shutdown Mode (LMV341-N) 0 to 1 0 to 0.8
5V AC Electrical Characteristics
(1)
Unless otherwise specified, all limits specified for T
J
= 25°C, V
+
= 5V, V
−
= 0V, V
CM
= V
+
/2, V
O
= V
+
/2 and R
L
> 1MΩ.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min Typ Max Units
(2) (3) (2)
SR Slew Rate R
L
= 10kΩ
(4)
1.0 V/µs
GBW Gain-Bandwidth Product R
L
= 10kΩ, C
L
= 200pF 1.0 MHz
Φ
m
Phase Margin R
L
= 100kΩ 70 deg
G
m
Gain Margin R
L
= 100kΩ 20 dB
e
n
Input-Referred Voltage Noise f = 1kHz 39 nV/√Hz
i
n
Input-Referred Current Noise f = 1kHz 0.001 pA/√Hz
THD Total Harmonic Distortion f = 1kHz, A
V
= +1 0.012 %
R
L
= 600Ω, V
IN
= 1V
PP
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self heating where T
J
> T
A
.
(2) All limits are specified by testing or statistical analysis.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) Connected as voltage follower with 2V
PP
step input. Number specified is the slower of the positive and negative slew rates.
Connection Diagram
Figure 1. 6-Pin SC70 Figure 2. 8-Pin VSSOP/SOIC Figure 3. 14-Pin TSSOP/SOIC
Top View Package Number DGK/D Package Number PW/D
Top View Top View
Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMV341-N LMV342-N LMV344-N