Datasheet
LMV301
www.ti.com
SNOS968A –MAY 2004–REVISED MAY 2013
1.8V DC Electrical Characteristics
Unless otherwise specified, all limits ensured for T
J
= 25°C. V
+
= 1.8V, V
−
= 0V, V
CM
= V
+
/2, V
O
= V
+
/2, and R
L
> 1MΩ.
Boldface limits apply at the temperature extremes.
Parameter Test Conditions Min
(1)
Typ
(2)
Max
(1)
Units
V
OS
Input Offset Voltage V
CM
= 0.4V, V
+
= 1.3V, = V
−
= −0.5V 0.9 8 mV
9
I
B
Input Bias Current 0.182 35 pA
50
I
S
Supply Current V
CM
= 0.4V, V
+
= 1.3V, = V
−
= −0.5V 150 250 µA
275
CMRR Common Mode Rejection Ratio 0.3V ≤ V
CM
≤ 0.9V 62 108 dB
60
PSRR Power Supply Rejection Ratio 1.8V ≤ V
+
≤ 5V, 67 110 dB
0.9 ≤ V
CM
≤ 2.5V 62
V
CM
Input Common-Mode Voltage For CMRR ≥ 50dB −0.3 0.6 V
Range 0
A
V
Large Signal Voltage Gain R
L
= 600Ω to 0V, V
+
= 1.2V, V
−
= −0.6V, 80 119
Sourcing V
O
= −0.2V to 0.8V, V
CM
= 0V 75
dB
R
L
= 2kΩ to 0V, V
+
= 1.2V, V
−
= −0.6V, V
O
80 111
= −0.2V to 0.8V, V
CM
= 0V 75
Sinking R
L
= 600Ω to 0V, V
+
= 1.2V, V
−
= −0.6V, 80 94
V
O
= −0.2V to 0.8V, V
CM
= 0V 75
dB
R
L
= 2kΩ to 0V, V
+
= 1.2V, V
−
= −0.6V, V
O
80 96
= −0.2V to 0.8V, V
CM
= 0V 75
V
O
Output Swing R
L
= 600Ω to 0.9V V
OH
1.65 1.72 V
V
IN
= ±100mV 1.63
V
OL
0.074 0.100 V
R
L
= 2kΩ to 0.9V V
OH
1.75 1.77 V
V
IN
= ±100mV 1.74
V
OL
0.024 0.035 V
0.040
I
O
Output Short Circuit Current Sourcing, 4 8.4 mA
V
O
= 0V, V
IN
= 100mV 3.3
Sinking, 7 9.8 mA
V
O
= 1.8V, V
IN
= −100mV
(1) All limits are ensured by testing or statistical analysis.
(2) Typical value represent the most likely parametric norm.
1.8V AC Electrical Characteristics
Unless otherwise specified, all limits ensured for T
J
= 25°C. V
+
= 1.8V, V
−
= 0V, V
CM
= V
+
/2, V
O
= V
+
/2, and R
L
> 1MΩ.
Boldface limits apply at the temperature extremes.
Parameter Test Conditions Typ
(1)
Units
SR Slew Rate See
(2)
0.57 V/µs
GBW Gain Bandwidth Product 1 MHz
φm Phase Margin 60 Deg
G
m
Gain Margin 10 dB
e
n
Input-Referred Voltage Noise f = 1kHz, V
CM
= 0.5V 40 nV/√Hz
f = 100kHz 30
THD Total Harmonic Distortion f = 1kHz, A
V
= +1 0.089 %
RL = 600kΩ, V
IN
= 1V
PP
(1) Typical value represent the most likely parametric norm.
(2) V
+
= 5V. Connected as voltage follower with 5V step input. Number specified is the slower of the positive and negative slew rates.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LMV301