Datasheet

LMV116, LMV118
www.ti.com SNOSA87B –OCTOBER 2003–REVISED MAY 2013
±5V Electrical Characteristics
Unless otherwise specified, all limits specified for at T
J
= 25°C, V
+
= 5V, V
−
= −5V, V
CM
= V
O
= 0V, and R
F
= 2kΩ, and R
L
=
1kΩ to V
+
/2. Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min
(1)
Typ
(2)
Max
(1)
Units
V
OS
Input Offset Voltage −5V ≤ V
CM
≤ 1.7V ±1 ±5 mV
±6
TC V
OS
Input Offset Average Drift See
(3)
±5 μV/C
I
B
Input Bias Current See
(4)
−2.0 −0.40 μA
−2.2
I
OS
Input Offset Current 3 500 nA
CMRR Common Mode Rejection Ratio V
CM
Stepped from −5V to 3.5V 78 104 dB
PSRR Power Supply Rejection Ratio V
+
= 5V to 6V or V
−
= −5V to −6V 72 95 dB
R
IN
Common Mode Input Resistance 3 MΩ
C
IN
Common Mode Input Capacitance 2 pF
CMVR Input Common-Mode Voltage CMRR ≥ 50dB −5.3 4.0 V
Range −5.1
A
VOL
Large Signal Voltage Gain V
O
= −2V to 2V 74 85 dB
71
V
O
Output Swing High R
L
= 1kΩ 4.70 4.92 V
R
L
= 10kΩ 4.97
Output Swing Low R
L
= 1kΩ −4.70 −4.93 mV
R
L
= 10kΩ −4.98
I
SC
Output Short Circuit Current Sourcing to 0V 40 57 mA
V
ID
= 200mV
(5)
Sinking to 0V 40 54
V
ID
= −200mV
(5)
I
OUT
Output Current V
OUT
= 0.5V from rails ±20 mA
I
S
Supply Current Normal Operation 600 900 μA
Shut-down Mode (LMV118) 15 50
SR Slew Rate
(6)
A
V
= +1, V
O
= 1V
PP
35 V/μs
BW −3dB BW A
V
= +1, V
OUT
= 200mV
PP
45 MHz
e
n
Input -Referred Voltage Noise f = 100kHz 40
nV/√Hz
f = 1kHz 60
i
n
Input-Referred Current Noise f = 100kHz 0.75
pA/√Hz
f = 1kHz 1.20
t
on
Turn-on Time (LMV118) 200 ns
t
off
Turn-off Time (LMV118) 700 ns
TH
SD
Shut-down Threshold (LMV118) I
S
≤ 50μA 4.25 4.60 V
I
SD
Shutdown Pin Input Current See
(4)
−20 μA
(LMV118)
(1) All limits are specified by testing or statistical analysis.
(2) Typical values represent the most likely parametric norm.
(3) Offset voltage average drift determined by dividing the change in V
OS
at temperature extremes into the total temperature change.
(4) Positive current corresponds to current flowing into the device.
(5) Short circuit test is a momentary test. See Absolute Maximum Ratings, Note 6.
(6) Slew rate is the average of the rising and falling slew rates.
Copyright © 2003–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMV116 LMV118