Datasheet

LMP2234
SNOSAW4D –SEPTEMBER 2007–REVISED MARCH 2013 www.ti.com
5V AC Electrical Characteristics
(1)
Unless otherwise specified, all limits are ensured for T
A
= 25°C, V
+
= 5V, V
−
= 0V, V
CM
= V
O
= V
+
/2, and R
L
> 1 MΩ. Boldface
limits apply at the temperature extremes.
Symbol Parameter Conditions Min Typ Max Units
(2) (3) (2)
GBWP Gain Bandwidth Product C
L
= 20 pF, R
L
= 10 kΩ 130 kHz
SR Slew Rate A
V
= +1 Falling Edge 33 58
32
V/ms
Rising Edge 33 48
32
θ
m
Phase Margin C
L
= 20 pF, R
L
= 10 kΩ 68 deg
G
m
Gain Margin C
L
= 20 pF, R
L
= 10 kΩ 27 dB
e
n
Input-Referred Voltage Noise Density f = 1 kHz 60 nV/√Hz
Input-Referred Voltage Noise 0.1 Hz to 10 Hz 2.3 μV
PP
i
n
Input-Referred Current Noise Density f = 1 kHz 10 fA/√Hz
THD+N Total Harmonic Distortion + Noise f = 100 Hz, R
L
= 10 kΩ 0.002 %
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where T
J
> T
A
. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
(2) All limits are specified by testing, statistical analysis or design.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
3.3V DC Electrical Characteristics
(1)
Unless otherwise specified, all limits are ensured for T
A
= 25°C, V
+
= 3.3V, V
−
= 0V, V
CM
= V
O
= V
+
/2, and R
L
> 1 MΩ.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min Typ Max Units
(2) (3) (2)
V
OS
Input Offset Voltage ±10 ±160 μV
±250
TCV
OS
Input Offset Voltage Drift LMP2234A ±0.3 ±0.75 μV/°C
LMP2234B ±0.3 ±2.5
I
BIAS
Input Bias Current ±0.02 ±1 pA
±50
I
OS
Input Offset Current ±5 fA
CMRR Common Mode Rejection Ratio 0V ≤ V
CM
≤ 2.3V 79 92 dB
77
PSRR Power Supply Rejection Ratio 1.6V ≤ V
+
≤ 5.5V 83 120 dB
V
CM
= 0V 82
CMVR Common Mode Voltage Range CMRR ≥ 78 dB −0.2 2.5 V
CMRR ≥ 77 dB −0.2 2.5
A
VOL
Large Signal Voltage Gain V
O
= 0.3V to 3V 108 120 dB
R
L
= 10 kΩ to V
+
/2 107
V
O
Output Swing High R
L
= 10 kΩ to V
+
/2 14 50 mV
V
IN
(diff) = 100 mV 50 from either
rail
Output Swing Low R
L
= 10 kΩ to V
+
/2 14 50
V
IN
(diff) = −100 mV 50
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. No ensured specification of parametric performance is indicated in the electrical
tables under conditions of internal self-heating where T
J
> T
A
. Absolute Maximum Ratings indicate junction temperature limits beyond
which the device may be permanently degraded, either mechanically or electrically.
(2) All limits are specified by testing, statistical analysis or design.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
4 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LMP2234