Datasheet

LMP2021, LMP2022
SNOSAY9E –SEPTEMBER 2008–REVISED MARGH 2013 www.ti.com
2.5V Electrical Characteristics
(1)
(continued)
Unless otherwise specified, all limits are ensured for T
A
= 25°C, V
+
= 2.5V, V
−
= 0V, V
CM
= V
+
/2, R
L
>10 kΩ to V
+
/2. Boldface
limits apply at the temperature extremes.
Symbol Parameter Conditions Min
(2)
Typ
(3)
Max
(2)
Units
V
OUT
Output Swing High R
L
= 10 kΩ to V
+
/2 38 50
70
R
L
= 2 kΩ to V
+
/2 62 85
mV
115
from either
Output Swing Low R
L
= 10 kΩ to V
+
/2 30 45
rail
55
R
L
= 2 kΩ to V
+
/2 58 75
95
I
OUT
Linear Output Current Sourcing, V
OUT
= 2V 30 50
mA
Sinking, V
OUT
= 0.5V 30 50
I
S
Supply Current Per Amplifier 0.95 1.10
mA
1.37
SR Slew Rate
(6)
A
V
= +1, C
L
= 20 pF, R
L
= 10 kΩ 2.5 V/μs
V
O
= 2 V
PP
GBW Gain Bandwidth Product C
L
= 20 pF, R
L
= 10 kΩ 5 MHz
G
M
Gain Margin C
L
= 20 pF, R
L
= 10 kΩ 10 dB
Φ
M
Phase Margin C
L
= 20 pF, R
L
= 10 kΩ 60 deg
C
IN
Input Capacitance Common Mode 12
pF
Differential Mode 12
e
n
Input-Referred Voltage Noise Density f = 0.1 kHz or 10 kHz, A
V
= 1000 11
nV/√Hz
f = 0.1 kHz or 10 kHz, A
V
= 100 15
Input-Referred Voltage Noise 0.1 Hz to 10 Hz 260
nV
PP
0.01 Hz to 10 Hz 330
i
n
Input-Referred Current Noise f = 1 kHz 350 fA/√Hz
t
r
Recovery time to 0.1%, R
L
= 10 kΩ, A
V
= −50,
50 µs
V
OUT
= 1.25 V
PP
Step, Duration = 50 μs
CT Cross Talk LMP2022, f = 1 kHz 150 dB
(6) The number specified is the average of rising and falling slew rates and is measured at 90% to 10%.
5V Electrical Characteristics
(1)
Unless otherwise specified, all limits are ensured for T
A
= 25°C, V
+
= 5V, V
−
= 0V, V
CM
= V
+
/2, R
L
> 10 kΩ to V
+
/2. Boldface
limits apply at the temperature extremes.
Symbol Parameter Conditions Min
(2)
Typ
(3)
Max
(2)
Units
V
OS
Input Offset Voltage −0.4 ±5
μV
±10
TCV
OS
Input Offset Voltage Drift
(4)
−0.004 ±0.02 μV/°C
I
B
Input Bias Current ±25 ±100 pA
±300
I
OS
Input Offset Current ±48 ±200
pA
±250
CMRR Common Mode Rejection Ratio −0.2V ≤ V
CM
≤ 4.2V 120
139 dB
0V ≤ V
CM
≤ 4.0V 115
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where T
J
> T
A
.
(2) All limits are specified by testing, statistical analysis or design.
(3) Typical values represent the most likely parametric norm at the time of characterization. Actual typical values may vary over time and
will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production
material.
(4) Offset voltage temperature drift is determined by dividing the change in V
OS
at the temperature extremes by the total temperature
change.
4 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMP2021 LMP2022