Datasheet

LMH6640
www.ti.com SNOSAA0B –FEB 2004–REVISED MARCH 2013
16V Electrical Characteristics
Unless otherwise specified, All limits specified for T
J
= 25°C, V
+
= 16V, V
−
= 0V, V
O
= V
CM
= V
+
/2 and R
L
= 2 kΩ to V
+
/2.
Boldface limits apply at temperature extremes.
(1)
Symbol Parameter Conditions Min
(2)
Typ
(3)
Max
(2)
Units
BW −3 dB Bandwidth A
V
= +1 (R
L
= 100Ω) 190
MHz
A
V
= −1 (R
L
= 100Ω) 60
BW
0.1 dB
0.1 dB Gain Flatness A
V
= −2.7 20 MHz
LSBW -3 dB Bandwidth A
V
= +1, V
O
= 2 V
PP
(R
L
= 100Ω) 35 MHz
GBW Gain Bandwidth Product A
V
= +1, (R
L
= 100Ω) 62 MHz
SR Slew Rate
(4)
A
V
= −1 170 V/μs
e
n
Input Referred Voltage Noise f = 10 kHz 23
nV/√Hz
f = 1 MHz 15
i
n
Input Referred Current Noise f = 10 kHz 1.1
pA/√Hz
f = 1 MHz 0.7
THD Total Harmonic Distortion f = 5 MHz, V
O
= 2 V
PP
, A
V
= +2 –64
dBc
R
L
= 1 kΩ to V
+
/2
t
s
Settling Time V
O
= 2 V
PP
, ±0.1%, A
V
= −1 35 ns
V
OS
Input Offset Voltage 1 5
mV
7
I
B
Input Bias Current
(5)
−1 −2.6
μA
−3.5
I
OS
Input Offset Current 34 800
nA
1800
CMVR Common Mode Input Voltage CMRR ≥ 50 dB –0.3 −0.2
Range −0.1
V
15.0 15.1
14.6
CMRR Common Mode Rejection Ratio V
−
≤ V
CM
≤ V
+
−1.5V 72 90 dB
A
VOL
Large Signal Voltage Gain V
O
= 15 V
PP
, R
L
= 2 kΩ to V
+
/2 86 95
82
dB
V
O
= 14 V
PP
, R
L
= 150Ω to V
+
/2 74 78
70
V
O
Output Swing High R
L
= 2 kΩ to V
+
/2 15.85 15.90
R
L
= 150Ω to V
+
/2 15.45 15.78
V
Output Swing Low R
L
= 2 kΩ to V
+
/2 0.10 0.15
R
L
= 150Ω to V
+
/2 0.21 0.55
I
SC
Output Short Circuit Current
(6)
Sourcing to V
+
/2 60 95
30
mA
Sinking from V
+
/2 50 75
15
I
OUT
Output Current V
O
= 0.5V from either Supply ±100 mA
PSRR Power Supply Rejection Ratio 15V ≤ V
+
≤ 17V 72 80 dB
I
S
Supply Current No Load 4 6.5
mA
7.8
R
IN
Common Mode Input Resistance A
V
= +1, f = 1 kHz, R
S
= 1 MΩ 32 MΩ
C
IN
Common Mode Input Capacitance A
V
= +1, R
S
= 100 kΩ 1.7 pF
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that T
J
= T
A
. Parametric performance is indicated in the electrical tables under conditions of
internal self-heating where T
J
> T
A
.
(2) All limits are specified by testing or statistical analysis.
(3) Typical Values represent the most likely parametric norm.
(4) Slew rate is the average of the rising and falling slew rates
(5) Positive current corresponds to current flowing into the device.
(6) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150 °C Short circuit test is a momentary test. Output short circuit duration is
infinite for V
S
< 6V at room temperature and below. For V
S
> 6V, allowable short circuit duration is 1.5 ms.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMH6640