Datasheet

LMH6517
www.ti.com SNOSB19K –NOVEMBER 2008–REVISED MARCH 2013
5V Electrical Characteristics
(1)
The following specifications apply for single supply with V+ = 5V, Maximum Gain , R
L
= 100Ω, V
OUT
= 2 V
PP
, fin = 150 MHz.
Boldface limits apply at temperature extremes.
Parameter Test Conditions Min
(2)
Typ
(3)
Max
(2)
Units
Dynamic Performance
SSBW Frequency Range 1200 MHz
Maximum Voltage Gain f = 200 MHz 22 dB
Input Noise Voltage Maximum Gain, f > 1MHz, R
IN
= 0 Ω 1.1 nV/√Hz
Output Noise Voltage Maximum Gain, f > 1MHz 22 nV/√Hz
Noise Figure Maximum Gain 5.5 dB
OIP3 Output Third Order Intercept Point f = 150 MHz, V
OUT
= 4dBm per tone 43 dBm
Output Third Order Intercept Point f = 200 MHz, V
OUT
= 4dBm per tone 43
IMD3 Third Order Intermodulation f = 150 MHz, V
OUT
= 4dBm per tone −78 dBc
Products
Third Order Intermodulation f = 200 MHz, V
OUT
= 4dBm per tone −78
Products
P1dB 1dB Compression Point f = 150 MHz, R
L
= 100Ω 18.3 dBm
1dB Compression Point f= 150 MHz, R
L
= 200Ω 15.5
Analog I/O
Input Resistance Differential 170 200 220 Ω
Input Capacitance 2 pF
Input Common Mode Voltage Self Biased 2.42 2.55 2.71
V
2.24 2.79
Input Common Mode Voltage Externally Driven, CMRR > 40dB 1.5 3.5 V
Range
Maximum Input Voltage Swing Volts peak to peak, differential 5.5 V
Output Common Mode Voltage Self Biased 2.4 2.55 2.7 V
Maximum DIfferential Output Differential 5.9 V
PP
Voltage Swing
Output Voltage Swing Single ended (each output) 1.05 1V to 4V 4.00 V
V
OS
Output Offset Voltage All Gain Settings −25 −2 25 mV
-30 30
CMRR Common Mode Rejection Ratio Maximum Gain, f=100MHz 60 dB
PSRR Power Supply Rejection Ratio Maximum Gain, f=100MHz 60 dB
XTLK Channel to Channel Crosstalk Maximum Gain, f=100MHz −85 dBc
XTLK Channel to Channel Crosstalk Maximum Gain, f=300MHz −72 dBc
Gain Parameters
Maximum Gain Gain Code 000000, 21.7 21.85 22
dB
DC Voltage Gain 21.65 22.05
Minimum Gain Gain Code 111111, −9.25 −9.5 −9.78
dB
DC Voltage Gain −9.1 −9.8
Gain Adjust Range 31.5 dB
Gain Step Size 0.5 dB
Channel Matching Gain Error between A and B channel. ±0.05 dB
Channel Matching Phase Shift between A and B channel. ±0.1 °
Gain Step Error Any two steps −0.3 ±0.05 0.3 dB
Gain Step Error Maximum Gain to Maximum Gain −12dB −0.5 ±0.1 0.5 dB
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. No specification of parametric performance
is indicated in the electrical tables under conditions different than those tested
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical
Quality Control (SQC) methods.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LMH6517