Datasheet

LME49713
SNAS386F –SEPTEMBER 2007–REVISED MARCH 2013 www.ti.com
ELECTRICAL CHARACTERISTICS
(1)(2)
The following specifications apply for the V
S
= ±15V, R
L
= 2kΩ, R
SOURCE
= 10Ω, f
IN
= 1kHz, and T
J
= 25°C, unless otherwise
specified.
LME49713
Units
Symbol Parameter Conditions
(Limits)
Typical
(3)
Limit
(4)
A
V
= 1, V
OUT
= 3V
RMS
, R
F
= 1.2kΩ
THD+N Total Harmonic Distortion + Noise R
L
= 100Ω, V
OUT
= 3V
RMS
0.0006 0.00071 % (max)
R
L
= 600Ω, V
OUT
= 1.4V
RMS
0.00036 0.00045 % (max)
A
V
= 1, V
IN
= 3V
RMS
IMD Intermodulation Distortion 0.00009 %
Two-tone, 60Hz & 7kHz 4:1
BW Bandwidth A
V
= –1, R
F
= 1.2kΩ 132 MHz
SR Slew Rate V
O
= 20V
P-P
, A
V
= –1 ±1900 V/μs
FPBW Full Power Bandwidth V
OUT
= 20V
P-P
, A
V
= –1 30 MHz
A
V
= –1, 10V step,
t
s
Settling time 50 ns
0.1% error range
μV
RMS
Equivalent Input Noise Voltage f
BW
= 20Hz to 20kHz 0.26 0.6
(max)
e
n
f = 1kHz 1.9 4.0 nV/√Hz
Equivalent Input Noise Density
f = 10Hz 11.5 (max)
i
n
f = 1kHz 16
Current Noise Density pA/√Hz
f = 10Hz 160
V
OS
Input Offset Voltage ±0.05 ±1.0 mV (max)
Average Input Offset Voltage Drift vs
ΔV
OS
/ΔTemp –40°C ≤ T
A
≤ 85°C 0.29 μV/°C
Temperature
Average Input Offset Voltage Shift vs
PSRR V
SUPPLY
= ±5V to ±15V
(5)
100 95 dB (min)
Power Supply Voltage
I
B
Input Bias Current V
CM
= 0V 1.8 6 μA (max)
–40°C ≤ T
A
≤ 85°C
Input Bias Current Drift vs
ΔI
OS
/ΔTemp Inverting input 4.5 nA/°C
Temperature
Non-inverting input 4.7 nA/°C
I
OS
Input Offset Current V
CM
= 0V 1.3 5 μA (max)
(V+) – 2.0 V (min)
V
IN-CM
Common-Mode Input Voltage Range ±13.5
(V-) + 2.0 V (min)
CMRR Common-Mode Rejection –10V<Vcm<10V 88 86 dB (min)
Non-inverting-input Input Impedance –10V<Vcm<10V 1.2 MΩ
Z
IN
Inverting-input Input Impedance –10V<Vcm<10V 58 Ω
V
OUT
= ±10V
Z
T
Transimpedance R
L
= 200Ω 4.2 2.0 MΩ (min)
R
L
= ∞ 4.7 2.65 MΩ (min)
R
L
= 150Ω ±11.1 ±10.3 V (min)
V
OUTMAX
Maximum Output Voltage Swing
R
L
= 600Ω ±11.6 ±11.4 V (min)
I
OUT
Output Current R
L
= 150Ω, V
S
= ±18V ±100 ±91 mA (min)
I
OUT-CC
Instantaneous Short Circuit Current ±140 mA
R
OUT
Output Resistance f
IN
= 5MHz, Open-Loop 10 Ω
I
S
Total Quiescent Current I
OUT
= 0mA 8.5 10 mA (max)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All
voltages are measured with respect to the ground pin, unless otherwise specified.
(2) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(3) Typical values represent most likely parametric norms at T
A
= +25ºC, and at the Recommended Operation Conditions at the time of
product characterization and are not ensured.
(4) Datasheet min/max specification limits are specified by test or statistical analysis.
(5) PSRR is measured as follows: V
OS
is measured at two supply voltages, ±5V and ±15V. PSRR = | 20log(ΔV
OS
/ΔV
S
) |.
4 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LME49713