Datasheet

LM567, LM567C
SNOSBQ4D –MAY 1999–REVISED MARCH 2013 www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS
(1)(2)(3)
Supply Voltage Pin 9V
Power Dissipation
(4)
1100 mW
V
8
15V
V
3
−10V
V
3
V
4
+ 0.5V
Storage Temperature Range −65°C to +150°C
Operating Temperature Range
LM567H −55°C to +125°C
LM567CH, LM567CM, LM567CN 0°C to +70°C
Soldering Information
PDIP Package
Soldering (10 sec.) 260°C
SOIC Package
Vapor Phase (60 sec.) 215°C
Infrared (15 sec.) 220°C
See http://www.ti.com for other methods of soldering surface mount devices.
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) Refer to RETS567X drawing for specifications of military LM567H version.
(4) The maximum junction temperature of the LM567 and LM567C is 150°C. For operating at elevated temperatures, devices in the TO-5
package must be derated based on a thermal resistance of 150°C/W, junction to ambient or 45°C/W, junction to case. For the DIP the
device must be derated based on a thermal resistance of 110°C/W, junction to ambient. For the SOIC package, the device must be
derated based on a thermal resistance of 160°C/W, junction to ambient.
ELECTRICAL CHARACTERISTICS
AC Test Circuit, T
A
= 25°C, V
+
= 5V
LM567 LM567C/LM567CM
Parameters Conditions Units
Min Typ Max Min Typ Max
Power Supply Voltage Range 4.75 5.0 9.0 4.75 5.0 9.0 V
Power Supply Current Quiescent R
L
= 20k 6 8 7 10 mA
Power Supply Current Activated R
L
= 20k 11 13 12 15 mA
Input Resistance 18 20 15 20 kΩ
Smallest Detectable Input Voltage I
L
= 100 mA, f
i
= f
o
20 25 20 25 mVrms
Largest No Output Input Voltage I
C
= 100 mA, f
i
= f
o
10 15 10 15 mVrms
Largest Simultaneous Outband Signal to
6 6 dB
Inband Signal Ratio
Minimum Input Signal to Wideband Noise B
n
= 140 kHz
−6 −6 dB
Ratio
Largest Detection Bandwidth 12 14 16 10 14 18 % of f
o
Largest Detection Bandwidth Skew 1 2 2 3 % of f
o
Largest Detection Bandwidth Variation with
±0.1 ±0.1 %/°C
Temperature
Largest Detection Bandwidth Variation with 4.75–6.75V
±1 ±2 ±1 ±5 %V
Supply Voltage
Highest Center Frequency 100 500 100 500 kHz
2 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM567 LM567C