Datasheet
LM7341
SNOSAW9B –MAY 2008–REVISED MARCH 2013
www.ti.com
±5V Electrical Characteristics
Unless otherwise specified, all limits ensured for T
A
= 25°C, V
+
= +5V, V
−
= −5V, V
CM
= V
OUT
= 0V and R
L
> 1 MΩ to 0V.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions Min
(1)
Typ
(2)
Max
(1)
Units
V
OS
Input Offset Voltage V
CM
= −4.5V and V
CM
= 4.5V −4 ±0.2 +4
mV
−5 +5
TCV
OS
Input Offset Voltage Temperature Drift ±2 μV/°C
I
B
Input Bias Current V
CM
= −4.5V −200 −95
−250
nA
V
CM
= 4.5V 35 70
80
I
OS
Input Offset Current V
CM
= −4.5V and V
CM
= 4.5V 1 40
nA
50
CMRR Common Mode Rejection Ratio −5V ≤ V
CM
≤ 3V 84 112
82
dB
−5V ≤ V
CM
≤ 5V 72 92
70
PSRR Power Supply Rejection Ratio 2.7V ≤ V
S
≤ 30V, V
CM
= −4.5V 86 106
dB
84
CMVR Common Mode Voltage Range CMRR ≥ 65 dB −5.3 −5.0
V
5.0 5.3
A
VOL
Open Loop Voltage Gain −4V ≤ V
O
≤ 4V 20 110
V/mV
R
L
= 10 kΩ to 0V 12
V
OUT
Output Voltage Swing R
L
= 10 kΩ to 0V, 80 150
High V
ID
= 100 mV 200
R
L
= 2 kΩ to 0V, 170 300
V
ID
= 100 mV 400
mV from
either rail
Output Voltage Swing R
L
= 10 kΩ to 0V 90 150
Low V
ID
= −100 mV 200
R
L
= 2 kΩ to 0V 210 300
V
ID
= −100 mV 400
I
OUT
Output Current Sourcing, V
OUT
= −5V 6 11
V
ID
= 200 mV 4
mA
Sinking, V
OUT
= 5V 6 12
V
ID
= −200 mV 4
I
S
Supply Current V
CM
= −4.5V and V
CM
= 4.5V 0.65 1.0
mA
1.1
SR Slew Rate ±4V Step 1.7 V/μs
GBW Gain Bandwidth f = 100 kHz, R
L
= 100 kΩ 4.0 MHz
e
n
Input Referred Voltage Noise Density f = 1 kHz 33 nV/√Hz
i
n
Input Referred Voltage Noise Density f = 1 kHz 0.26 pA/√Hz
THD+N Total Harmonic Distortion + Noise f = 10 kHz −66 dB
t
PD
Propagation Delay Overdrive = 50 mV
(3)
8
µs
Overdrive = 1V
(3)
6
t
r
Rise Time 20% to 80%
(3)
5 µs
t
f
Fall Time 80% to 20%
(3)
5 µs
(1) All limits are specified by testing or statistical analysis.
(2) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(3) The maximum differential voltage between the input pins is V
IN
Differential = ±15V.
4 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM7341