Datasheet

LM6211
www.ti.com SNOSAH2C –FEBRUARY 2006–REVISED MARCH 2013
5V Electrical Characteristics
(1)
(continued)
Unless otherwise specified, all limits are ensured for T
A
= 25°C, V
+
= 5V, V
−
= 0V, V
CM
= V
O
= V
+
/2. Boldface limits apply at
the temperature extremes.
Symbol Parameter Conditions Min
(2)
Typ
(3)
Max
(2)
Units
A
VOL
Large Signal Voltage Gain V
O
= 0.35V to 4.65, R
L
= 2 kΩ to V
+
/2 82 110
80
dB
V
O
= 0.25V to 4.75, R
L
= 10 kΩ to V
+
/2 85 110
82
V
O
Output Swing High R
L
= 2 kΩ to V
+
/2 50 150
165
R
L
= 10 kΩ to V
+
/2 20 85
90
mV from
rail
Output Swing Low R
L
= 2 kΩ to V
+
/2 39 150
170
R
L
= 10 kΩ to V
+
/2 13 85
90
I
OUT
Output Short Circuit Current Sourcing to V
+
/2 13 16
V
ID
= 100 mV
(7)
10
mA
Sinking to V
+
/2 20 30
V
ID
= −100 mV
(7)
10
I
S
Supply Current 0.96 1.10
mA
1.25
SR Slew Rate A
V
= +1, 10% to 90%
(8)
5.5 V/μs
GBW Gain Bandwidth Product 17 MHz
e
n
Input-Referred Voltage Noise f = 10 kHz 5.5
nV/√Hz
f = 1 kHz 6.0
i
n
Input-Referred Current Noise f = 1 kHz 0.01 pA/√Hz
THD Total Harmonic Distortion A
V
= 2, R
L
= 600Ω to V
+
/2 0.01 %
(7) The device is short circuit protected and can source or sink its limit currents continuously. However, care should be taken such that
when the output is driving short circuit currents, the inputs do not see more than ±0.3V differential voltage.
(8) Slew rate is the average of the rising and falling slew rates.
24V Electrical Characteristics
(1)
Unless otherwise specified, all limits are ensured for T
A
= 25°C, V
+
= 24V, V
−
= 0V, V
CM
= V
O
= V
+
/2. Boldface limits apply at
the temperature extremes.
Symbol Parameter Conditions Min
(2)
Typ
(3)
Max
(2)
Units
V
OS
Input Offset Voltage V
CM
= 0.5V 0.25 ±2.7
mV
±3.0
TC V
OS
Input Offset Average Drift V
CM
= 0.5V
(4)
±2 μV/C
I
B
Input Bias Current V
CM
= 0.5V
(5) (6)
2 25 pA
10 nA
I
OS
Input Offset Current V
CM
= 0.5V 0.1 pA
CMRR Common Mode Rejection Ratio 0 ≤ V
CM
≤ 21V 85 105
dB
0.4 ≤ V
CM
≤ 20V 70
PSRR Power Supply Rejection Ratio V
+
= 5V to 24V, V
CM
= 0.5V 85 98
78
dB
V
+
= 4.5V to 25V, V
CM
= 0.5V 80 98
CMVR Input Common-Mode Voltage CMRR ≥ 65 dB 0 21.5
V
Range CMRR ≥ 60 dB 0 20.5
(1) Electrical table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using the
Statistical Quality Control (SQC) method.
(3) Typical values represent the most likely parametric norm at the time of characterization.
(4) Offset voltage average drift is determined by dividing the change in V
OS
at the temperature extremes into the total temperature change.
(5) Positive current corresponds to current flowing into the device.
(6) Input bias current is ensured by design.
Copyright © 2006–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM6211