Datasheet

LM4811
www.ti.com
SNAS119D DECEMBER 2000REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1)(2)
Supply Voltage 6.0V
Storage Temperature 65°C to +150°C
ESD Susceptibility
(3)
2.5kV
ESD Susceptibility Machine model
(4)
200V
Junction Temperature (T
J
) 150°C
Vapor Phase (60 sec.) 215°C
Soldering Information DGS0010A Package Infrared (15 sec.) 220°C
θ
JA
DGS0010A 194°C/W
θ
JC
DGS0010A 52°C/W
θ
JA
NGY0010A
(5)
63°C/W
Thermal Resistance
θ
JC
NGY0010A
(5)
12°C/W
θ
JA
NHD0010A
(5)
63°C/W
θ
JC
NHD0010A
(5)
12°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Human body model, 100pF discharged through a 1.5k resistor.
(4) Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage, then
discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50 Ohms).
(5) The NGY0010A or NHD0010A package has its ExposedDAP soldered to an exposed 2in
2
area of 1oz printed circuit board copper.
Operating Ratings
Temperature Range T
MIN
T
A
T
MAX
40°C T
A
85°C
Supply Voltage 2.0V V
CC
5.5V
Electrical Characteristics
(1)(2)
The following specifications apply for V
DD
= 5V unless otherwise specified, limits apply to T
A
= 25°C.
LM4811
Units
Parameter Test Conditions
(Limits)
Typ
(3)
Limit
(4)
V
DD
Supply Voltage 2.0 V (min)
5.5 V (max)
I
DD
Supply Current V
IN
= 0V, I
O
= 0A 1.3 3.0 mA
I
SD
Shutdown Current V
IN
= 0V 0.3 µA
V
OS
Output Offset Voltage V
IN
= 0V 4.0 50 mV
P
O
Output Power 0.1% THD+N; f = 1kHz
R
L
= 16 105 mW
R
L
= 32 70 mW
THD+N Total Harmonic Distortion P
O
= 50mW, R
L
= 32 0.3 %
f = 20Hz to 20kHz
Crosstalk Channel Separation R
L
= 32; f = 1kHz; 100 dB
P
O
= 70mW
PSRR Power Supply Rejection Ratio C
B
= 1.0µF, V
RIPPLE
= 100mV
PP
60 dB
f = 217Hz
V
IH
(CLOCK, UP/DN, SHUTDOWN) 1.4 V (min)
Input Voltage High
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) All voltages are measured with respect to the ground pin, unless otherwise specified.
(3) Typical specifications are specified at +25°C and represent the most likely parametric norm.
(4) Tested limits are ensured to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are ensured by design,
test, or statistical analysis.
Copyright © 2000–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM4811