Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp Audio TO 99 8

LM4562

www.ti.com

SNAS326J –AUGUST 2006–REVISED APRIL 2013

LM4562 Dual High-Performance, High-Fidelity Audio Operational Amplifier

Check for Samples: LM4562

FEATURES

DESCRIPTION

The LM4562 is part of the ultra-low distortion, low-

• Easily Drives 600Ω Loads

noise, high-slew-rate operational amplifier series

• Optimized for Superior Audio Signal Fidelity

optimized and fully specified for high-performance,

• Output Short Circuit Protection

high-fidelity applications. Combining advanced

leading-edge process technology with state-of-the-art

• PSRR and CMRR Exceed 120dB (Typ)

circuit design, the LM4562 audio operational

• SOIC, PDIP, and TO-99 Packages

amplifiers deliver superior audio signal amplification

for outstanding audio performance. The LM4562

APPLICATIONS

combines extremely low voltage noise density

(2.7nV/√Hz) with vanishingly low THD+N (0.00003%)

• Ultra High-Quality Audio Amplification

to easily satisfy the most demanding audio

• High-Fidelity Preamplifiers

applications. To ensure that the most challenging

• High-Fidelity Multimedia

loads are driven without compromise, the LM4562

has a high slew rate of ±20V/μs and an output current

• State-of-the-Art Phono Pre Amps

capability of ±26mA. Further, dynamic range is

• High-Performance Professional Audio

maximized by an output stage that drives 2kΩ loads

• High-Fidelity Equalization and Crossover

to within 1V of either power supply voltage and to

Networks

within 1.4V when driving 600Ω loads.

• High-Performance Line Drivers

The LM4562's outstanding CMRR (120dB), PSRR

• High-Performance Line Receivers

(120dB), and V

(0.1mV) give the amplifier excellent

operational amplifier DC performance.

• High-Fidelity Active Filters

The LM4562 has a wide supply range of ±2.5V to

KEY SPECIFICATIONS

±17V. Over this supply range the LM4562’s input

circuitry maintains excellent common-mode and

• Power Supply Voltage Range: ±2.5V to ± 17V

power supply rejection, as well as maintaining its low

• THD+N (A

= 1, V

OUT

= 3V

RMS

, f

= 1kHz)

input bias current. The LM4562 is unity gain stable.

– R

= 2kΩ: 0.00003% (typ)

This Audio Operational Amplifier achieves

outstanding AC performance while driving complex

– R

= 600Ω: 0.00003% (typ)

loads with values as high as 100pF.

• Input Noise Density: 2.7nV/√Hz (typ)

The LM4562 is available in an 8-lead narrow body

• Slew Rate: ±20V/μs (typ)

SOIC, an 8-lead PDIP, and an 8-lead TO-99.

• Gain Bandwidth Product: 55MHz (typ)

Demonstration boards are available for each

• Open Loop Gain (R

= 600Ω): 140dB (typ)

package.

• Input Bias Current: 10nA (typ)

• Input Offset Voltage: 0.1mV (typ)

• DC Gain Linearity Error: 0.000009%

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (41 pages)

PAGE 1
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 LM4562 Dual High-Performance, High-Fidelity Audio Operational Amplifier Check for Samples: LM4562 FEATURES DESCRIPTION • • • • • The LM4562 is part of the ultra-low distortion, lownoise, high-slew-rate operational amplifier series optimized and fully specified for high-performance, high-fidelity applications.
PAGE 2
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL APPLICATION 150: 3320: 150: 3320: 26.1 k: + 909: - - LM4562 + INPUT LM4562 + 3.83 k: + 100: 22 nF//4.7 nF//500 pF 10 pF 47 k: OUTPUT 47 nF//33 nF A. 1% metal film resistors, 5% polypropylene capacitors Figure 1.
PAGE 3
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 + V 8 OUTPUT A 1 INVERTING INPUT A 2 NON-INVERTING INPUT A OUTPUT B 7 6 3 5 INVERTING INPUT B NON-INVERTING INPUT B 4 V - Figure 3. 8-Lead TO-99 (LMC Package) These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.
PAGE 4
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS FOR THE LM4562 (1) (2) The specifications apply for VS = ±15V, RL = 2kΩ, fIN = 1kHz, TA = 25°C, unless otherwise specified. Symbol THD+N Parameter Total Harmonic Distortion + Noise Conditions LM4562 Typical (3) AV = 1, VOUT = 3Vrms RL = 2kΩ RL = 600Ω 0.00003 0.00003 AV = 1, VOUT = 3VRMS Two-tone, 60Hz & 7kHz 4:1 0.00005 Limit (4) Units (Limits) % (max) 0.
PAGE 5
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 ELECTRICAL CHARACTERISTICS FOR THE LM4562(1)(2) (continued) The specifications apply for VS = ±15V, RL = 2kΩ, fIN = 1kHz, TA = 25°C, unless otherwise specified.
PAGE 6
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS 0.01 THD+N vs Output Voltage VCC = 15V, VEE = –15V RL = 2kΩ 0.01 0.005 0.005 0.002 0.002 0.001 THD+N (%) THD+N (%) 0.001 0.0005 0.0002 0.0005 0.0002 0.0001 0.0001 0.00005 0.00005 0.00002 0.00002 0.00001 10m THD+N vs Output Voltage VCC = 12V, VEE = –12V RL = 2kΩ 100m 1 0.00001 10m 10 20 OUTPUT VOLTAGE (V) Figure 4. Figure 5.
PAGE 7
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) 0.01 THD+N vs Output Voltage VCC = 17V, VEE = –17V RL = 600Ω THD+N vs Output Voltage VCC = 2.5V, VEE = –2.5V RL = 600Ω 0.01 0.005 0.005 0.002 0.002 0.001 THD + N (%) THD+N (%) 0.001 0.0005 0.0002 0.0001 0.0005 0.0002 0.0001 0.00005 0.00005 0.00002 0.00002 0.00001 10m 100m 1 0.
PAGE 8
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) THD+N vs Frequency VCC = 15V, VEE = –15V, VOUT = 3VRMS RL = 2kΩ THD+N vs Frequency VCC = 12V, VEE = –12V, VOUT = 3VRMS RL = 2kΩ 0.01 0.005 0.005 0.002 0.002 0.001 0.001 0.0005 0.0005 % % 0.01 0.0002 0.0002 0.0001 0.0001 0.00005 0.00005 0.00002 0.00002 0.00001 20 50 100 200 500 1k 2k 0.00001 20 5k 10k 20k 5k 10k 20k Figure 16. Figure 17.
PAGE 9
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) THD+N vs Frequency VCC = 15V, VEE = –15V, VOUT = 3VRMS RL = 10kΩ THD+N vs Frequency VCC = 12V, VEE = –12V, VOUT = 3VRMS RL = 10kΩ 0.002 0.002 0.001 0.001 0.0005 0.0005 % 0.01 0.005 % 0.01 0.005 0.0002 0.0002 0.0001 0.0001 0.00005 0.00005 0.00002 0.00002 0.00001 20 50 100 200 500 1k 2k 5k 10k 20k 0.00001 20 Hz 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 22. Figure 23.
PAGE 10
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 0.01 0.005 0.005 0.002 0.002 0.001 0.001 0.0005 0.0005 IMD (%) IMD (%) 0.01 IMD vs Output Voltage VCC = 17V, VEE = –17V RL = 2kΩ 0.0002 0.0001 0.0002 0.0001 0.00005 0.00005 0.00002 0.00002 0.00001 0.000007 100m 200m 500m 1 2 5 0.00001 0.000006 100m 200m 500m 1 10 OUTPUT VOLTAGE (V) Figure 29.
PAGE 11
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) IMD vs Output Voltage VCC = 12V, VEE = –12V RL = 10kΩ 0.01 0.005 0.005 0.002 0.002 0.001 0.001 0.0005 0.0005 IMD (%) IMD (%) 0.01 0.0002 0.0001 0.0002 0.0001 0.00005 0.00005 0.00002 0.00002 0.00001 0.000006 100m 200m 500m 1 2 5 IMD vs Output Voltage VCC = 17V, VEE = –17V RL = 10kΩ 0.00001 0.000006 100m 200m 500m 1 10 OUTPUT VOLTAGE (V) Figure 34. 5 10 Figure 35.
PAGE 12
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Crosstalk vs Frequency VCC = 12V, VEE = –12V, VOUT = 3VRMS AV = 0dB, RL = 2kΩ +0 +0 -10 -20 -30 -40 -50 -10 -20 -30 -40 -50 CROSSTALK (dB) CROSSTALK (dB) Crosstalk vs Frequency VCC = 15V, VEE = –15V, VOUT = 10VRMS AV = 0dB, RL = 2kΩ -60 -70 -80 -90 -60 -70 -80 -90 -100 -100 -110 -110 -120 -130 20 -120 -130 20 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 41.
PAGE 13
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Crosstalk vs Frequency VCC = 15V, VEE = –15V, VOUT = 10VRMS AV = 0dB, RL = 600Ω +0 +0 -10 -20 -30 -40 -50 -10 -20 -30 -40 -50 CROSSTALK (dB) CROSSTALK (dB) Crosstalk vs Frequency VCC = 15V, VEE = –15V, VOUT = 3VRMS AV = 0dB, RL = 600Ω -60 -70 -80 -90 -60 -70 -80 -90 -100 -100 -110 -110 -120 -130 20 -120 -130 20 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 47.
PAGE 14
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Crosstalk vs Frequency VCC = 2.5V, VEE = –2.
PAGE 15
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) CROSSTALK (dB) +0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 20 Crosstalk vs Frequency VCC = 2.5V, VEE = –2.5V, VOUT = 1VRMS AV = 0dB, RL = 10kΩ 50 100 200 500 1k 2k 5k 10k 20k +0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 20 50 100 200 500 1k 2k FREQUENCY (Hz) Figure 58. Figure 59.
PAGE 16
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.
PAGE 17
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) PSRR– vs Frequency VCC = 12V, VEE = –12V RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 20 PSRR (dB) PSRR (dB) PSRR+ vs Frequency VCC = 12V, VEE = –12V RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp 100 1k 10k -110 -120 -130 -140 20 100k 200k 100 100k 200k Figure 71.
PAGE 18
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) PSRR+ vs Frequency VCC = 17V, VEE = –17V RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp PSRR– vs Frequency VCC = 17V, VEE = –17V RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp -110 -120 -130 -140 20 PSRR (dB) PSRR (dB) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 100 1k 10k FREQUENCY (Hz) -110 -120 -130 -140 20 100k 200k 1k 10k 100k 200k Figure 76. Figure 77. PSRR+ vs Frequency VCC = 2.
PAGE 19
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) PSRR– vs Frequency VCC = 2.5V, VEE = –2.5V RL = 600Ω, f = 200kHz, VRIPPLE = 200mVpp 0 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 20 PSRR (dB) PSRR (dB) PSRR+ vs Frequency VCC = 2.5V, VEE = –2.
PAGE 20
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 0 -20 -20 -40 -40 -60 -60 -80 -80 -100 -100 100 1k 10k FREQUENCY (Hz) -120 10 100k 200k 100k 200k CMRR vs Frequency VCC = 17V, VEE = –17V RL = 600Ω CMRR vs Frequency VCC = 2.5V, VEE = –2.5V RL = 600Ω -20 -20 -40 -40 -60 -60 -80 -80 -100 -100 100 1k 10k -120 10 100k 200k 100 1k 10k 100k 200k FREQUENCY (Hz) FREQUENCY (Hz) Figure 90. Figure 91.
PAGE 21
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) CMRR vs Frequency VCC = 2.5V, VEE = –2.5V RL = 10kΩ 0 -20 -20 -40 -40 CMRR (dB) 0 -60 -60 -80 -80 -100 -100 OUTPUT (Vrms) -120 10 100 1k 10k 100k 200k -120 10 100 1k 10k 100k 200k FREQUENCY (Hz) FREQUENCY (Hz) Figure 94. Figure 95. Output Voltage vs Load Resistance VDD = 15V, VEE = –15V THD+N = 1% Output Voltage vs Load Resistance VDD = 12V, VEE = –12V THD+N = 1% 11.
PAGE 22
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 14 Output Voltage vs Supply Voltage RL = 2kΩ, THD+N = 1% 12 10 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 12 10 8 6 4 8 6 4 2 2 0 2.5 14 Output Voltage vs Supply Voltage RL = 600Ω, THD+N = 1% 4.5 6.5 0 2.5 8.5 10.5 12.5 14.5 16.5 18.5 4.5 6.5 8.5 10.5 12.5 14.5 16.5 18.5 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Figure 100. Figure 101.
PAGE 23
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Full Power Bandwidth vs Frequency 0 160 o GAIN (dB), PHASE LAG ( ) 180 -2 MAGNITUDE (dB) Gain Phase vs Frequency 2 0 dB = 1 VP-P -4 -6 -8 -10 -12 -14 140 120 100 80 60 40 20 -16 0 -18 -20 10 1 10 100 1k 10k 100k 1M 10M 100M 10000000 100000 1000000 100000000 10000 FREQUENCY (Hz) 1000 100 FREQUENCY (Hz) Figure 106. Figure 107.
PAGE 24
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com APPLICATION INFORMATION DISTORTION MEASUREMENTS The vanishingly low residual distortion produced by LM4562 is below the capabilities of all commercially available equipment. This makes distortion measurements just slightly more difficult than simply connecting a distortion meter to the amplifier’s inputs and outputs. The solution, however, is quite simple: an additional resistor.
PAGE 25
LM4562 www.ti.com A. SNAS326J – AUGUST 2006 – REVISED APRIL 2013 Complete shielding is required to prevent induced pick up from external sources. Always check with oscilloscope for power line noise. Figure 111. Noise Measurement Circuit Total Gain: 115 dB @f = 1 kHz Input Referred Noise Voltage: en = V0/560,000 (V) Figure 112. RIAA Preamp Voltage Gain, RIAA Deviation vs Frequency Figure 113.
PAGE 26
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com TYPICAL APPLICATIONS AV = 34.5 F = 1 kHz En = 0.38 μV A Weighted Figure 114. NAB Preamp Figure 115. NAB Preamp Voltage Gain vs Frequency VO = V1–V2 Figure 116.
PAGE 27
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 VO = V1 + V2 − V3 − V4 Figure 117. Adder/Subtracter Figure 118. Sine Wave Oscillator Illustration is f0 = 1 kHz Figure 119.
PAGE 28
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 www.ti.com Illustration is f0 = 1 kHz Figure 120. Second-Order Low-Pass Filter (Butterworth) Illustration is f0 = 1 kHz, Q = 10, ABP = 1 Figure 121.
PAGE 29
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 Figure 122. AC/DC Converter Figure 123. 2-Channel Panning Circuit (Pan Pot) Figure 124.
PAGE 30
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 fL | fH | www.ti.com 1 1 , fLB | 2S R1C1 2S R 2 C1 1 1 , fHB | 2S R 5 C 2 2S ( R1 + R5 + 2R3) C2 The equations started above are simplifications, providing guidance of general –3dB point values, when the potentiometers are at their null position. Illustration is: fL ≈ 32 Hz, fLB ≈ 320 Hz fH ≈ 11 kHz, fHB ≈ 1.1 kHz Figure 125.
PAGE 31
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 Av = 35 dB En = 0.33 μV S/N = 90 dB f = 1 kHz A Weighted A Weighted, VIN = 10 mV @f = 1 kHz Figure 126. RIAA Preamp Illustration is: V0 = 101(V2 − V1) Figure 127.
PAGE 32
LM4562 SNAS326J – AUGUST 2006 – REVISED APRIL 2013 A. www.ti.com See Table 1. Figure 128. 10-Band Graphic Equalizer Table 1. C1, C2, R1, and R2 Values for Figure 128 (1) fo (Hz) C1 C2 R1 R2 32 0.12μF 4.7μF 75kΩ 500Ω 64 0.056μF 3.3μF 68kΩ 510Ω 125 0.033μF 1.5μF 62kΩ 510Ω 250 0.015μF 0.82μF 68kΩ 470Ω 500 8200pF 0.39μF 62kΩ 470Ω 1k 3900pF 0.22μF 68kΩ 470Ω 2k 2000pF 0.1μF 68kΩ 470Ω 4k 1100pF 0.056μF 62kΩ 470Ω 8k 510pF 0.022μF 68kΩ 510Ω 16k 330pF 0.
PAGE 33
LM4562 www.ti.com SNAS326J – AUGUST 2006 – REVISED APRIL 2013 REVISION HISTORY Rev Date 1.0 08/16/06 Description Initial release. 1.1 08/22/06 Updated the Instantaneous Short Circuit Current specification. 1.2 09/12/06 Updated the three ±15V CMRR Typical Performance Curves. 1.3 09/26/06 Updated interstage filter capacitor values on page 1 Typical Application schematic. 1.4 05/03/07 Added the “general note” under the EC table. 1.5 10/17/07 Replaced all the PSRR curves. 1.
PAGE 34
PACKAGE OPTION ADDENDUM www.ti.
PAGE 35
PACKAGE OPTION ADDENDUM www.ti.com 18-Oct-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties.
PAGE 36
PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM4562MAX/NOPB Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 5.4 2.0 8.0 W Pin1 (mm) Quadrant 12.
PAGE 37
PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4562MAX/NOPB SOIC D 8 2500 367.0 367.0 35.
PAGE 38
PAGE 39
PAGE 40
PAGE 41
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.