Datasheet

LM4041-N, LM4041-N-Q1
www.ti.com SNOS641F –OCTOBER 1999–REVISED JULY 2013
LM4041-N/LM4041-N-Q1 ADJ (Adjustable) Electrical Characteristics (Industrial Temperature
Range)
Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
; all other limits T
J
= 25°C unless otherwise specified (SOT-23, see
(1)
),
I
RMIN
≤ I
R
≤ 12 mA, V
REF
≤ V
OUT
≤ 10V. The grades C and D designate initial Reference Voltage Tolerances of ±0.5% and
±1%, respectively for V
OUT
= 5V.
Symbol Parameter Conditions Typical
(2)
LM4041CIM3 LM4041DIM3 Units
LM4041QCIM3 LM4041QDIM3 (Limit)
LM4041CIZ LM4041DIZ
LM4041CIM7 LM4041DIM7
(3) (3)
V
REF
Reference Voltage I
R
= 100 μA, V
OUT
= 5V 1.233 V
Reference Voltage I
R
= 100 μA, V
OUT
= 5V ±6.2 ±12 mV (max)
Tolerance
(4)
±14 ±24 mV (max)
I
RMIN
Minimum Operating 45 μA
Current
60 65 μA (max)
65 70 μA (max)
ΔV
REF
/ΔI
R
Reference Voltage I
RMIN
≤ I
R
≤ 1 mA 0.7 mV
Change with Operating SOT-23: V
OUT
≥ 1.6V
(6)
1.5 2.0 mV (max)
Current Change
(5)
2.0 2.5 mV (max)
1 mA ≤ I
R
≤ 12 mA 2 mV
SOT-23: V
OUT
≥ 1.6V
(6)
4 6 mV (max)
6 8 mV (max)
ΔV
REF
/ΔV Reference Voltage I
R
= 1 mA −1.55 mV/V
O
Change with Output
−2.0 −2.5 mV/V (max)
Voltage Change
−2.5 −3.0 mV/V (max)
I
FB
Feedback Current 60 nA
100 150 nA (max)
120 200 nA (max)
ΔV
REF
/ΔT Average Reference V
OUT
= I
R
= 10 mA 20 ppm/°C
Voltage Temperature 5V,
I
R
= 1 mA 15 ±100 ±150 ppm/°C (max)
Coefficient
(4)
I
R
= 100 μA 15 ppm/°C
Z
OUT
Dynamic Output I
R
= 1 mA, f = 120 Hz,
Impedance
I
AC
= 0.1 I
R
V
OUT
= V
REF
0.3 Ω
V
OUT
= 10V 2 Ω
e
N
Wideband Noise I
R
= 100 V
OUT
= V
REF
20 μV
rms
μA
10 Hz ≤ f ≤ 10 kHz
ΔV
REF
Reference Voltage Long t = 1000 hrs, I
R
= 100 μA, 120 ppm
Term Stability T = 25°C ±0.1°C
V
HYST
Thermal Hysteresis
(7)
ΔT = −40°C to +125°C 0.08 %
(1) When V
OUT
≤ 1.6V, the LM4041-N ADJ in the SOT-23 package must operate at reduced I
R
. This is caused by the series resistance of
the die attach between the die (-) output and the package (-) output pin. See the Output Saturation (SOT-23 only) curve in the Typical
Performance Characteristics section.
(2) Typicals are at T
J
= 25°C and represent most likely parametric norm.
(3) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(4) Reference voltage and temperature coefficient will change with output voltage. See Typical Performance Characteristics curves.
(5) Load regulation is measured on pulse basis from no load to the specified load current. Ouput changes due to die temperature change
must be taken into account separately.-
(6) When V
OUT
≤ 1.6V, the LM4041-N ADJ in the SOT-23 package must operate at reduced I
R
. This is caused by the series resistance of
the die attach between the die (-) output and the package (-) output pin. See the Output Saturation (SOT-23 only) curve in the Typical
Performance Characteristics section.
(7) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature +125°C.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM4041-N, LM4041-N-Q1