Datasheet
SLCS143A − APRIL 2004 − REVISED APRIL 2008
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, V
CC±
= ±15 V (unless otherwise noted)
PARAMETER TEST CONDITIONS
T
A
†
MIN TYP
‡
MAX UNIT
V
IO
Input offset voltage
See Note 7
25°C 0.7 3
mV
V
IO
Input offset voltage See Note 7
Full range 4
mV
I
IO
Input offset current
See Note 7
25°C 4 10
nA
I
IO
Input offset current See Note 7
Full range 20
nA
I
IB
Input bias current
V
O
= 1 V to 14 V
25°C 75 100
nA
I
IB
Input bias current V
O
= 1 V to 14 V
Full range 150
nA
I
IL(S)
Low-level strobe current
(see Note 8)
V
(strobe)
= 0.3 V, V
ID
≤ −10 mV 25°C −3 mA
V
ICR
Common-mode input voltage
range
Full range
13
to
−14.5
13.8
to
−14.7
V
A
VD
Large-signal differential voltage
amplification
V
O
= 5 V to 35 V, R
L
= 1 kΩ 25°C 40 200 V/mV
High-level (collector) output
I
(strobe)
= −3 mA, V
ID
= 5 mV,
V
OH
= 35 V
25°C 0.2 10 nA
I
OH
High-level (collector) output
leakage current
I
(strobe)
= −3 mA, V
ID
= 5 mV
,
V
OH
= 35 V
Full range
0.5 µA
I
OH
leakage current
V
ID
= 5 mV, V
OH
= 35 V 25°C nA
I
OL
= 50 mA
V
ID
= −5 mV 25°C 0.75 1.5
V
OL
Low-level (collector-to-emitter)
I
OL
= 50 mA
V
ID
= −10 mV 25°C
V
V
OL
Low-level (collector-to-emitter)
output voltage
V
CC+
= 4.5 V, V
CC−
= 0,
V
ID
= −6 mV Full range 0.23 0.4
V
output voltage
V
CC+
= 4.5 V, V
CC−
= 0,
I
OL
= 8 mA
V
ID
= −10 mV Full range
I
CC+
Supply current from V
CC+
,
output low
V
ID
= −10 mV, No load 25°C 5.1 6 mA
I
CC−
Supply current from V
CC−
,
output high
V
ID
= 10 mV, No load 25°C −4.1 −5 mA
†
Unless otherwise noted, all characteristics are measured with BALANCE and BAL/STRB open and EMIT OUT grounded.
Full range for LM211Q is −40°C to 125°C.
‡
All typical values are at T
A
= 25°C.
NOTES: 7. The offset voltages and offset currents given are the maximum values required to drive the collector output up to 14 V or down to
1 V with a pullup resistor of 7.5 kΩ to V
CC+
. These parameters actually define an error band and take into account the worst-case
effects of voltage gain and input impedance.
8. The strobe should not be shorted to ground; it should be current driven at −3 mA to −5 mA (see Figures 13 and 27).
switching characteristics, V
CC±
= ±15 V, T
A
= 25°C
PARAMETER TEST CONDITIONS TYP UNIT
Response time, low-to-high-level output
R
C
= 500 Ω to 5 V,
C
L
= 5 pF,
See Note 9
115 ns
Response time, high-to-low-level output
R
C
= 500
Ω
to 5 V,
C
L
= 5 pF,
See Note 9
165 ns
NOTE 9: The response time specified is for a 100-mV input step with 5-mV overdrive and is the interval between the input step function and the
instant when the output crosses 1.4 V.