Datasheet

LM1117-N, LM1117I
SNOS412M –FEBRUARY 2000–REVISED MARCH 2013 www.ti.com
LM1117I ELECTRICAL CHARACTERISTICS (continued)
Typicals and limits appearing in normal type apply for T
J
= 25°C. Limits appearing in Boldface type apply over the entire
junction temperature range for operation, −40°C to 125°C.
Symbol Parameter Conditions Min
(1)
Typ
(2)
Max
(1)
Units
ΔV
OUT
Line Regulation
(3)
LM1117I-ADJ
I
OUT
= 10mA, 1.5V ≤ V
IN
-V
OUT
≤ 13.75V 0.035 0.3 %
LM1117I-3.3
I
OUT
= 0mA, 4.75V ≤ V
IN
≤ 15V 1 10 mV
LM1117I-5.0
I
OUT
= 0mA, 6.5V ≤ V
IN
≤ 15V 1 15 mV
ΔV
OUT
Load Regulation
(3)
LM1117I-ADJ
V
IN
-V
OUT
= 3V, 10 ≤ I
OUT
≤ 800mA 0.2 0.5 %
LM1117I-3.3
V
IN
= 4.75V, 0 ≤ I
OUT
≤ 800mA 1 15 mV
LM1117I-5.0
V
IN
= 6.5V, 0 ≤ I
OUT
≤ 800mA 1 20 mV
V
IN
-V
OUT
Dropout Voltage
(4)
I
OUT
= 100mA 1.10 1.30 V
I
OUT
= 500mA 1.15 1.35 V
I
OUT
= 800mA 1.20 1.40 V
I
LIMIT
Current Limit V
IN
-V
OUT
= 5V, T
J
= 25°C 800 1200 1500 mA
Minimum Load LM1117I-ADJ
Current
(5)
V
IN
= 15V 1.7 5 mA
Quiescent Current LM1117I-3.3
V
IN
≤ 15V 5 15 mA
LM1117I-5.0
V
IN
≤ 15V 5 15 mA
Thermal Regulation T
A
= 25°C, 30ms Pulse 0.01 0.1 %/W
Ripple Regulation f
RIPPLE
=1 20Hz, V
IN
-V
OUT
= 3V V
RIPPLE
= 60 75 dB
1V
PP
Adjust Pin Current 60 120 μA
Adjust Pin Current 10 ≤ I
OUT
≤ 800mA,
Change 1.4V ≤ V
IN
-V
OUT
≤ 10V 0.2 10 μA
Temperature Stability 0.5 %
Long Term Stability T
A
= 125°C, 1000Hrs 0.3 %
RMS Output Noise (% of V
OUT
), 10Hz ≤ f ≤10kHz 0.003 %
Thermal Resistance 3-Lead SOT-223 15.0 °C/W
Junction-to-Case
3-Lead TO-263 10 °C/W
Thermal Resistance 3-Lead SOT-223 (No heat sink) 136 °C/W
Junction-to-Ambient
3-Lead TO-263 (No heat sink)
(6)
92 °C/W
No air flow)
8-Lead WSON
(7)
40 °C/W
(3) Load and line regulation are measured at constant junction room temperature.
(4) The dropout voltage is the input/output differential at which the circuit ceases to regulate against further reduction in input voltage. It is
measured when the output voltage has dropped 100mV from the nominal value obtained at V
IN
= V
OUT
+1.5V.
(5) The minimum output current required to maintain regulation.
(6) Minimum pad size of 0.038in
2
(7) Thermal Performance for the WSON was obtained using JESD51-7 board with six vias and an ambient temperature of 22°C. For
information about improved thermal performance and power dissipation for the WSON, refer to Application Note AN-1187 (SNOA401).
6 Submit Documentation Feedback Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LM1117-N LM1117I