Datasheet

TMS570LS1224
SPNS190B –OCTOBER 2012–REVISED FEBRUARY 2015 www.ti.com
7.11.5 SPI Slave Mode I/O Timings
Table 7-35. SPI Slave Mode External Timing Parameters (CLOCK PHASE = 0, SPICLK = input, SPISIMO =
input, and SPISOMI = output)
(1)(2)(3)(4)
NO. Parameter MIN MAX Unit
1 t
c(SPC)S
Cycle time, SPICLK
(5)
40 ns
2
(6)
t
w(SPCH)S
Pulse duration, SPICLK high (clock polarity = 0) 14 ns
t
w(SPCL)S
Pulse duration, SPICLK low (clock polarity = 1) 14
3
(6)
t
w(SPCL)S
Pulse duration, SPICLK low (clock polarity = 0) 14 ns
t
w(SPCH)S
Pulse duration, SPICLK high (clock polarity = 1) 14
4
(6)
t
d(SPCH-SOMI)S
Delay time, SPISOMI valid after SPICLK high (clock t
rf(SOMI)
+ 20 ns
polarity = 0)
t
d(SPCL-SOMI)S
Delay time, SPISOMI valid after SPICLK low (clock polarity t
rf(SOMI)
+ 20
= 1)
5
(6)
t
h(SPCH-SOMI)S
Hold time, SPISOMI data valid after SPICLK high (clock 2 ns
polarity =0)
t
h(SPCL-SOMI)S
Hold time, SPISOMI data valid after SPICLK low (clock 2
polarity =1)
6
(6)
t
su(SIMO-SPCL)S
Setup time, SPISIMO before SPICLK low (clock polarity = 4 ns
0)
t
su(SIMO-SPCH)S
Setup time, SPISIMO before SPICLK high (clock polarity = 4
1)
7
(6)
t
h(SPCL-SIMO)S
Hold time, SPISIMO data valid after SPICLK low (clock 2 ns
polarity = 0)
t
h(SPCH-SIMO)S
Hold time, SPISIMO data valid after S PICLK high (clock 2
polarity = 1)
8 t
d(SPCL-SENAH)S
Delay time, SPIENAn high after last SPICLK low (clock 1.5t
c(VCLK)
2.5t
c(VCLK)
+t
r(ENAn)
+ ns
polarity = 0) 22
t
d(SPCH-SENAH)S
Delay time, SPIENAn high after last SPICLK high (clock 1.5t
c(VCLK)
2.5t
c(VCLK)
+ t
r(ENAn)
+
polarity = 1) 22
9 t
d(SCSL-SENAL)S
Delay time, SPIENAn low after SPICSn low (if new data t
f(ENAn)
t
c(VCLK)
+t
f(ENAn)
+27 ns
has been written to the SPI buffer)
(1) The MASTER bit (SPIGCR1.0) is cleared and the CLOCK PHASE bit (SPIFMTx.16) is cleared.
(2) If the SPI is in slave mode, the following must be true: t
c(SPC)S
≥ (PS + 1) t
c(VCLK)
, where PS = prescale value set in SPIFMTx.[15:8].
(3) For rise and fall timings, see Table 5-7.
(4) t
c(VCLK)
= interface clock cycle time = 1 /f
(VCLK)
(5) When the SPI is in Slave mode, the following must be true:
For PS values from 1 to 255: t
c(SPC)S
≥ (PS +1)t
c(VCLK)
≥ 40ns, where PS is the prescale value set in the SPIFMTx.[15:8] register bits.
For PS values of 0: t
c(SPC)S
= 2t
c(VCLK)
≥ 40ns.
(6) The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPIFMTx.17).
150 Peripheral Information and Electrical Specifications Copyright © 2012–2015, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TMS570LS1224