Datasheet

14
CC1350
SWRS183 –JUNE 2016 www.ti.com
Submit Documentation Feedback
Product Folder Links: CC1350
Specifications Copyright © 2016, Texas Instruments Incorporated
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
(3) Excluding one exception at F
wanted
/ 2, per Bluetooth Specification.
5.8 1-Mbps GFSK (Bluetooth low energy) – RX
Measured on the TI CC1350_7XD-Dual Band reference design with T
c
= 25°C, V
DDS
= 3.0 V, f
RF
= 2440 MHz, unless
otherwise noted. All tests with Bluetooth low energy PHY (1 Mbps), 37 byte payload unless otherwise noted.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Receiver sensitivity
Differential mode. Measured at the
CC1350_7XD-Dual Band SMA connector, 37
byte payload BER = 10
–3
–87 dBm
Receiver sensitivity
Differential mode. Measured at the
CC1350_7XD-Dual Band SMA connector, 255
byte payload BER = 10
–3
-86 dBm
Receiver saturation
Differential mode. Measured at the
CC1350_7XD-Dual Band SMA connector, BER
= 10
–3
0 dBm
Frequency error tolerance
Difference between the incoming carrier
frequency and the internally generated carrier
frequency. Input signal 10 dB above sensitivity
limit
–350 350 kHz
Data rate error tolerance
Difference between incoming data rate and the
internally generated data rate. Input signal 10
dB above sensitivity limit
–750 750 ppm
Co-channel rejection
(1)
Wanted signal at –67 dBm, modulated interferer
in channel, BER = 10
–3
–6 dB
Selectivity, ±1 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at ± 1 MHz, BER = 10
–3
7 / 4
(2)
dB
Selectivity, +2 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at +2 MHz, BER = 10
–3
38 dB
Selectivity, ±3 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at ± 3 MHz, BER = 10
–3
Note that -3 MHz is -1
MHz from the image frequency.
36 / 41
(2)
dB
Selectivity, ±4 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at ± 4 MHz, BER = 10
–3
39 / 38
(2)
dB
Selectivity, ±5 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at ± 5 MHz, BER = 10
–3
35 / 39
(2)
dB
Selectivity, ±6 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at ≥ ±6 MHz, BER = 10
–3
42 / 37
(2)
dB
Selectivity, ±15 MHz or more
(1)
Wanted signal at –67 dBm, modulated interferer
at ≥ ±15 MHz or more, BER = 10
–3
55 dB
Selectivity, Image frequency
(image compensation enabled,
the image compensation is
calibrated in production)
(1)
Wanted signal at –67 dBm, modulated interferer
at image frequency, BER = 10
–3
37 dB
Selectivity, Image frequency
±1 MHz
(1)
Wanted signal at –67 dBm, modulated interferer
at ± 1 MHz from image (-3 MHz and -1 MHz from
wanted) frequency, BER = 10
–3
4 / 41
(2)
dB
Out-of-band blocking
(3)
30 MHz to 2000 MHz –25 dBm
Out-of-band blocking 2003 MHz to 2399 MHz >–20 dBm
Out-of-band blocking 2484 MHz to 2997 MHz >–20 dBm
Out-of-band blocking 3000 MHz to 12.75 GHz >–30 dBm
Intermodulation
Wanted signal at 2402 MHz, –64 dBm. Two
interferers at 2405 and 2408 MHz, respectively,
at the given power level
–30 dBm
Spurious emissions,
30 to 1000 MHz
Conducted measurement in a 50-Ω single-ended
load. Suitable for systems targeting compliance
with EN 300 328, EN 300 440 class 2, FCC
CFR47, Part 15 and ARIB STD-T-66
–72 dBm